HP Integrity rx8620 Installation Guide, Sixth Edition - HP Integrity rx8620 Se - Page 76

Connecting the CE Tool to the Local RS-232 Port on the MP, Serial Port

Get HP Integrity rx8620 PDF manuals and user guides View all HP Integrity rx8620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Installation Cabling and Power Up If the CE Tool is a laptop using Reflection 1, check or change these communications settings using the following procedure: 1. From the Reflection 1 Main screen, pull down the Connection menu and select Connection Setup. 2. Select Serial Port. 3. Select Com1. 4. Check the settings and change, if required. Go to More Settings to set Xon/Xoff. Click OK to close the More Settings window. 5. Click OK to close the Connection Setup window. 6. Pull down the Setup menu and select Terminal (under the Emulation tab). 7. Select the VT100 HP terminal type. 8. Click Apply. This option is not highlighted if the terminal type you want is already selected. 9. Click OK. Connecting the CE Tool to the Local RS-232 Port on the MP This connection allows direct communications with the MP. Only one window can be created on the CE Tool to monitor the MP. When enabled, it provides direct access to the MP and any partition. Use the following procedure to connect the CE Tool to the local RS-232 port on the MP: 76 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Chapter 2
Installation
Cabling and Power Up
76
If the CE Tool is a laptop using Reflection 1, check or change these communications settings using the
following procedure:
1. From the Reflection 1 Main screen, pull down the
Connection
menu and select
Connection Setup
.
2. Select
Serial Port
.
3. Select
Com1
.
4. Check the settings and change, if required.
Go to
More Settings
to set Xon/Xoff. Click
OK
to close the More Settings window.
5. Click
OK
to close the Connection Setup window.
6. Pull down the
Setup
menu and select
Terminal
(under the
Emulation
tab).
7. Select the VT100 HP terminal type.
8. Click
Apply
.
This option is not highlighted if the terminal type you want is already selected.
9. Click
OK
.
Connecting the CE Tool to the Local RS-232 Port on the MP
This connection allows direct communications with the MP.
Only one window can be created
on the CE
Tool to monitor the MP. When enabled, it provides direct access to the MP and any partition.
Use the following procedure to connect the CE Tool to the local RS-232 port on the MP: