HP Integrity rx8620 Installation Guide, Sixth Edition - HP Integrity rx8620 Se - Page 78

Fault, Attention, Remote, MP Present, Standby Power, Power, Switch

Get HP Integrity rx8620 PDF manuals and user guides View all HP Integrity rx8620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Installation Cabling and Power Up The preferred tool is the CE Tool running Reflection 1. To power on the MP, set up a communications link, and log in to the MP: 1. Apply power to the server cabinet. Apply power to any other server cabinets that were shipped to the customer site. On the front of the server, a solid green Standby Power, and a solid green MP Present light will illuminate after about 30 seconds. Figure 2-30 Front Panel Display RUN Attention Fault Remote MP Present Standby Power Power Power Switch 2. Check the bulk power supply (BPS) LED for each BPS. See Figure 2-31 for the LED location. When on, the breakers distribute power to the BPS. AC power is present at the BPS: • When power is first applied. Note the BPS LEDs will be flashing amber. • After 30 seconds have elapsed. Note the flashing amber BPS LED for each BPS becomes a flashing green LED. 78 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Chapter 2
Installation
Cabling and Power Up
78
The preferred tool is the CE Tool running Reflection 1.
To power on the MP, set up a communications link, and log in to the MP:
1. Apply power to the server cabinet.
Apply power to any other server cabinets that were shipped to the customer site.
On the front of the server, a solid green
Standby Power
, and a solid green
MP Present
light will
illuminate after about 30 seconds.
Figure 2-30
Front Panel Display
2. Check the bulk power supply (BPS) LED for each BPS. See Figure 2-31 for the LED location.
When on, the breakers distribute power to the BPS. AC power is present at the BPS:
•
When power is first applied. Note the BPS LEDs will be flashing amber.
•
After 30 seconds have elapsed. Note the flashing amber BPS LED for each BPS becomes a flashing
green LED.
RUN
Fault
Attention
Remote
MP Present
Standby Power
Power
Power
Switch