HP Integrity rx8620 Installation Guide, Sixth Edition - HP Integrity rx8620 Se - Page 82

Accessing the Management Processor via a Web Browser, The ls Command Screen

Get HP Integrity rx8620 PDF manuals and user guides View all HP Integrity rx8620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Installation Cabling and Power Up 9. To check the LAN parameters and status, enter the ls command at the MP Command Menu prompt (MP:CM>). 10. A screen similar to the following will display allowing verification of the settings: Figure 2-34 The ls Command Screen To return to the MP main menu, enter ma. To exit the MP, enter x at the MP main menu. Accessing the Management Processor via a Web Browser Web browser access is an embedded feature of the management processor (MP). The Web browser allows access to the server via the LAN port on the core I/O card. MP configuration must be done from an ASCII console. NOTE The MP has a separate LAN port from the system LAN port. It requires a separate LAN drop, IP address, and networking information from that of the port used by HP-UX. Before starting this procedure, the following information is required: • IP address for the MP LAN • Subnet mask • Gateway address • Hostname (this is used when messages are logged or printed) To configure the LAN port for a Web browser, perform the following steps: 82 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Chapter 2
Installation
Cabling and Power Up
82
9. To check the LAN parameters and status, enter the
ls
command at the MP Command Menu prompt
(
MP:CM>
).
10. A screen similar to the following will display allowing verification of the settings:
Figure 2-34
The ls Command Screen
To return to the MP main menu, enter
ma
.
To exit the MP, enter
x
at the MP main menu.
Accessing the Management Processor via a Web Browser
Web browser access is an embedded feature of the management processor (MP). The Web browser allows
access to the server via the LAN port on the core I/O card. MP configuration must be done from an ASCII
console.
NOTE
The MP has a separate LAN port from the system LAN port. It requires a separate LAN drop,
IP address, and networking information from that of the port used by HP-UX.
Before starting this procedure, the following information is required:
•
IP address for the MP LAN
•
Subnet mask
•
Gateway address
•
Hostname (this is used when messages are logged or printed)
To configure the LAN port for a Web browser, perform the following steps: