HP Integrity rx8620 Installation Guide, Sixth Edition - HP Integrity rx8620 Se - Page 62

PCI I/O Slot Details, Gate Closed, Gate Open

Get HP Integrity rx8620 PDF manuals and user guides View all HP Integrity rx8620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Installation Installing Accessories NOTE A slow, firm pressure is needed to properly seat the card into the backplane. Step 5. Flip the PCI gate for the card slot to the closed position. CAUTION Working out of sequence or not completing the actions within each step could cause the system to crash. Do not press the attention button until the latch is locked. Step 6. Press the attention button. The green power LED will start to blink. Figure 2-18 PCI I/O Slot Details Gate Closed Gate Open Attention Button Power LED (Green) Attention LED (Yellow) Step 7. Wait for the green power LED to stop blinking and turn on solid. Step 8. Check for errors in the hotplugd daemon log file (default: /var/adm/hotplugd.log). The critical resource analysis (CRA) performed while doing an attention button initiated add action is very restrictive and the action will not complete-it will fail-to protect critical resources from being impacted. For finer control over CRA actions use pdweb or the olrad command. Refer to the Interface Card OL* Support Guide located on the Web at http://docs.hp.com for details. Step 9. Replace the top cover. Step 10. Connect all cables to the installed PCI card. 62 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Chapter 2
Installation
Installing Accessories
62
NOTE
A slow, firm pressure is needed to properly seat the card into the backplane.
Step 5.
Flip the PCI gate for the card slot to the closed position.
CAUTION
Working out of sequence or not completing the actions within each step could cause
the system to crash.
Do not press the attention button until the latch is locked.
Step 6.
Press the attention button.
The green power LED will start to blink.
Figure 2-18 PCI I/O Slot Details
Step 7.
Wait for the green power LED to stop blinking and turn on solid.
Step 8.
Check for errors in the hotplugd daemon log file (default: /var/adm/hotplugd.log).
The critical resource analysis (CRA) performed while doing an attention button initiated add action
is very restrictive and the action will not complete–it will fail–to protect critical resources from
being impacted. For finer control over CRA actions use pdweb or the olrad command. Refer to the
Interface Card OL* Support Guide located on the Web at http://docs.hp.com for details.
Step 9.
Replace the top cover.
Step 10.
Connect all cables to the installed PCI card.
Gate Closed
Gate Open
Power LED (Green)
Attention LED (Yellow)
Attention Button