HP Integrity rx8620 Installation Guide, Sixth Edition - HP Integrity rx8620 Se - Page 73

Installing the Line Cord Anchor (rack mounted servers), On/Off, Four Cell Server Installation rp8400

Get HP Integrity rx8620 PDF manuals and user guides View all HP Integrity rx8620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Installation Cabling and Power Up INTERVAL THREE With the On/Off switch on the front of the server set to On, the intake fans spin up and become noticeably audible while the LED indicator remains solid green. The BPS LED indicator turns a solid green and the PCI backplane power supply LED indicators turn solid green. The hard disk drive LED turns green briefly and then the LED turns off. Installing the Line Cord Anchor (rack mounted servers) The line cord anchor is attached to the rear of the server when rack mounted. It provides a method to secure the line cords to the server, preventing accidental removal of the cords from the server. Four Cell Server Installation (rp8400, rp8420, rp8440, rx8620, rx8640) There are holes pre-drilled, and captive nuts pre-installed in the server chassis. To install the line cord anchor: 1. Align the line cord anchor thumbscrews with the corresponding captive nuts at the rear of the chassis. Refer to Figure 2-27, "Four Cell Line Cord Anchor (rp8400, rp8420, rp8440, rx8620, rx8640)," Figure 2-27 Four Cell Line Cord Anchor (rp8400, rp8420, rp8440, rx8620, rx8640) 2. Tighten the captive thumbscrews to secure the line cord anchor to the chassis. 3. Weave the power cables through the line cord anchor. Leave enough slack that the plugs can be disconnected from the receptacles without removing the cords from the line cord anchor Chapter 2 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Chapter 2
Installation
Cabling and Power Up
73
INTERVAL THREE
With the
On/Off
switch on the front of the server set to
On
, the intake fans spin up and become noticeably
audible while the LED indicator remains solid green. The BPS LED indicator turns a solid green and the PCI
backplane power supply LED indicators turn solid green. The hard disk drive LED turns green briefly and
then the LED turns off.
Installing the Line Cord Anchor (rack mounted servers)
The line cord anchor is attached to the rear of the server when rack mounted. It provides a method to secure
the line cords to the server, preventing accidental removal of the cords from the server.
Four Cell Server Installation (rp8400, rp8420, rp8440, rx8620, rx8640)
There are holes pre-drilled,
and captive nuts pre-installed in the server chassis.
To install the line cord anchor:
1. Align the line cord anchor thumbscrews with the corresponding captive nuts at the rear of the chassis.
Refer to Figure 2-27, “Four Cell Line Cord Anchor (rp8400, rp8420, rp8440, rx8620, rx8640),”
Figure 2-27
Four Cell Line Cord Anchor (rp8400, rp8420, rp8440, rx8620, rx8640)
2. Tighten the captive thumbscrews to secure the line cord anchor to the chassis.
3. Weave the power cables through the line cord anchor. Leave enough slack that the plugs can be
disconnected from the receptacles without removing the cords from the line cord anchor