JVC GY-DV500U GY-DV500 User Manual - PDF (4,089KB) - Page 37

Detaching the Battery Case From the GY-DV500 and Attaching The Anton, Bauer Battery, Attaching - gy dv500 power supply

Get JVC GY-DV500U - Professional Dv Camcorder PDF manuals and user guides View all JVC GY-DV500U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

4. POWER SUPPLY 4-2 Battery Pack Operation (Cont'd) Using an Anton-Bauer Battery Pack To use an Anton-Bauer battery pack (Propack 13/14, Trimpack 13/14, Magnum 13/14, Compack 13/14 Series), it is necessary to detach the battery case from the GY-DV500 and replace it with the Anton-Bauer battery holder. Use the following battery holder. • Battery holder: Anton-Bauer QRQ27 Detaching the Battery Case From the GY-DV500 and Attaching The AntonBauer Battery Attaching the Anton-Bauer Battery Holder Anton-Bauer Battery Holder 1. Black screw A 1. Remove the two black screws A on the battery case. 2. Remove the lower half of the battery case cover in the downward direction. Connector Compartment 3. Mount screw B 3. Connector 3. Mount screw B 3. To remove the battery case, remove the four screws B fixing the battery case and the connector connecting the battery case to this unit. Anton-Bauer Battery holder 4. Connect the connectors protruding from the GY-DV500 with the connectors on the battery holder. * Following connection of the connectors, insert them into the connector compartment and secure with the clamp. 5. Secure the battery holder to the GY-DV500 with the four mount screws provided with the battery holder. * Take care not to pinch the wires. This could result in damage. Attaching and Detaching an Anton-Bauer Battery Pack Release lever Side panel with display Guide pins Cassette cover side panel Guide holes (x3) Battery pack (Trimpack) Release lever LIGHT ON OFF COUNTER CTL TC UB Battery Attaching the Battery Pack 1. Align the 3 guide pins of the battery pack with the guide holes on the battery holder, and push straight to insert the battery pack. The battery cannot be attached properly if the guide pins are not inserted straight. 2. Slide the battery pack toward the side panel where the cassette cover is located until it clicks. Now the battery pack has been attached. Detaching the Battery Pack Ⅲ While pushing and holding the release lever, slide the battery pack toward the side panel where the LCD display is located, then pull the battery pack outward to remove. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
37
4. POWER SUPPLY
4.
Connect the connectors protruding from the GY-DV500 with
the connectors on the battery holder.
*
Following connection of the connectors, insert them into
the connector compartment and secure with the clamp.
5.
Secure the battery holder to the GY-DV500 with the four
mount screws provided with the battery holder.
* Take care not to pinch the wires. This could result in
damage.
Using an Anton-Bauer Battery Pack
To use an Anton-Bauer battery pack (Propack 13/14, Trimpack 13/14, Magnum 13/14, Compack 13/14 Series), it is necessary to
detach the battery case from the GY-DV500 and replace it with the Anton-Bauer battery holder. Use the following battery holder.
• Battery holder: Anton-Bauer QRQ27
Detaching the Battery Case From the GY-DV500 and Attaching The Anton-
Bauer Battery
1.
Remove the two black screws
A
on the battery case.
2.
Remove the lower half of the battery case cover in the
downward direction.
Attaching and Detaching an Anton-Bauer Battery Pack
Attaching the Battery Pack
1.
Align the 3 guide pins of the battery pack with
the guide holes on the battery holder, and push
straight to insert the battery pack.
The battery cannot be attached properly if the
guide pins are not inserted straight.
2.
Slide the battery pack toward the side panel
where the cassette cover is located until it clicks.
Now the battery pack has been attached.
Detaching the Battery Pack
n
While pushing and holding the release lever, slide
the battery pack toward the side panel where the
LCD display is located, then pull the battery pack
outward to remove.
3.
To remove the battery case, remove the four screws
B
fixing
the battery case and the connector connecting the battery
case to this unit.
Attaching the Anton-Bauer Battery Holder
Anton-Bauer Battery Holder
4-2
Battery Pack Operation (Cont'd)
1.
Black screw
A
3.
Mount screw
B
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
3.
Connector
3.
Mount screw
B
Guide pins
Battery pack
(Trimpack)
Release lever
Cassette cover
side panel
Guide
holes
(x3)
Side panel
with display
Battery
Release
lever
Anton-Bauer
Battery holder
Connector
Compartment