JVC GY-DV500U GY-DV500 User Manual - PDF (4,089KB) - Page 57

Time Code Presetting Procedure, Presetting User's Bit Data

Get JVC GY-DV500U - Professional Dv Camcorder PDF manuals and user guides View all JVC GY-DV500U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

9. TIME CODE OPERATION TIME CODE PRESETTING PROCEDURE 2. HOLD button 4. SHIFT button CH-1 AUDIO LEVEL CH-2 LITHIUM BATT. CH-1 CH-2 TC GENERATOR AUTO MANUAL PRESET REGEN AUDIO SELECT FREE REC AUDIO INPUT CH-1 CH-2 CONTINUE MENU FRONT REAR GROUP HOLD ITEM SELECT DATA SET SHIFT ADVANCE PRESET 3. ADVANCE button HOLD H M S F HOLD H M S F HOLD H M S F HOLD H M S F 6. PRESET button 1. Display the time code on the counter display. Set the COUNTER switch to "TC". • Time code up to 23 hrs. 59 min. 59 sec. 29 frames can be preset. 2. Place the time code generator in preset mode. Press the HOLD button. • The "HOLD" indicator lights on the display to indicate the preset mode. The first digit of the counter display blinks. 3. Set the value of the blinking digit. Press the ADVANCE button. • The value of the blinking digit changes. 4. Change the blinking digit. Press the SHIFT button. • The blinking digit changes. 5. Set the desired value for all digits. Repeat steps 3. and 4. for each digit. 6. Preset the set data in the memory. Press the PRESET button. • The set data is saved as the time code generator value. Following the above operation, the "HOLD" indicator disappears from the display, the counter stops blinking and the time code is preset. • If the REC/FREE switch is set to FREE, the time code starts to run. Ⅲ If you preset a wrong time code, perform steps 2. 3. 4. 5. and 6. again. Note: Time code presetting is not possible in the SAVE mode. PRESETTING USER'S BIT DATA RESET button OPERATE/WARNING RESET MONITOR SELECT CH 1 CH 2 40 30 20 32k 48k AUD LOCK SP MENU REMAIN H OVER AUTO OFF DEW 10 0 dB OVER SERVO RF L i PB NDF HOLD H M S F REV FWD E BATT F M LIGHT ON OFF COUNTER CTL TC UB Ⅲ Display user's bit data on the counter display and perform the same procedure as the time code presetting procedure. • The user's bit can be specified using numerals or alphabetic letters from 0 to F for each digit. Note: Do not set "F" to all user's bit, or the data can not be read. • Pressing the RESET button in the preset mode resets the time code or user's bit data to 00 00 00 00. • If you press the HOLD button by mistake, press the HOLD button once more to return to the previous display. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
57
9. TIME CODE OPERATION
TC GENERATOR
FREE
REC
PRESET
REGEN
CH-1
CH-2
CH-1
CH-2
CH-1
CH-2
CONTINUE
MENU
PRESET
ADVANCE
SHIFT
HOLD
AUTO
MANUAL
FRONT
REAR
DATA SET
SELECT
ITEM
GROUP
AUDIO SELECT
AUDIO INPUT
AUDIO
LEVEL
LITHIUM BATT.
4.
SHIFT button
6.
PRESET
button
3.
ADVANCE
button
2.
HOLD button
H
M
S
F
HOLD
H
M
S
F
HOLD
H
M
S
F
HOLD
H
M
S
F
HOLD
TIME CODE PRESETTING PROCEDURE
1.
Display the time code on the counter display.
Set the COUNTER switch to "TC".
•
Time code up to 23 hrs. 59 min. 59 sec. 29 frames can be
preset.
2.
Place the time code generator in preset mode.
Press the HOLD button.
•
The "HOLD" indicator lights on the display to indicate
the preset mode. The first digit of the counter display
blinks.
3.
Set the value of the blinking digit.
Press the ADVANCE button.
•
The value of the blinking digit changes.
4.
Change the blinking digit.
Press the SHIFT button.
•
The blinking digit changes.
5.
Set the desired value for all digits.
Repeat steps
3.
and
4.
for each digit.
6.
Preset the set data in the memory.
Press the PRESET button.
•
The set data is saved as the time code generator value.
Following the above operation, the "HOLD" indicator
disappears from the display, the counter stops blinking
and the time code is preset.
•
If the REC/FREE switch is set to FREE, the time code
starts to run.
n
If you preset a wrong time code, perform steps
2
.
3
.
4
.
5.
and
6.
again.
PRESETTING USER'S BIT DATA
n
Display user's bit data on the counter display and perform
the same procedure as the time code presetting procedure.
•
The user's bit can be specified using numerals or alphabetic
letters from 0 to F for each digit.
•
Pressing the RESET button in the preset mode resets
the time code or user's bit data to 00 00 00 00.
•
If you press the HOLD button by mistake, press the HOLD
button once more to return to the previous display.
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
E
REV
FWD
F
BATT
H
H
M
M
S
F
REMAIN
AUD LOCK
32k
CH 1
CH 2
48k
PB
NDF
AUTO OFF
DEW
L i
RF
SERVO
HOLD
SP
MENU
OVER
OVER
40 30
20
10
0
dB
RESET button
Note:
Do not set “F” to all user's bit, or the data can not be read.
Note:
Time code presetting is not possible in the SAVE mode.