JVC SR-V10U SR-V10U Instruction manual (1MB, PDF) - Page 49
Locate end point - svhs
View all JVC SR-V10U manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 49 highlights
1 Make connections Connect an audio/video cable between the VCR's audio/video input connectors and the other component's audio/video output connectors. 2 Prepare tapes Load the source tape on the other VCR, and the tape to be edited on this VCR. 3 Select input mode Select "F-1" - when connecting the other component to the audio/video input connectors on the front panel. Select "L-1" - when connecting the other component to the audio/video input connectors on the rear panel. On the front panel: Push the JOG dial, then turn it to the left or right. On the Remote: Press the Number key "0 (AUX)" and/or CH +/-. 4 Select video input terminal Follow the procedure described on pages 37 and 40. When using S VIDEO terminal, set "FRONT AUX INPUT" (or "REAR AUX INPUT" if you use the connectors on the rear) to "S-VIDEO". When using VIDEO terminal, set "FRONT AUX INPUT" (or "REAR AUX INPUT") to "VIDEO". 5 Select edit mode On this VCR, set "PICTURE CONTROL" to "EDIT" by following the procedure described on pages 37 and 38. 6 Locate end point 1 Press PLAY ( 3 ) to start playback. 2 Press PAUSE ( 8 ) when you find the end of the scene for which you want to edit. 3 Press C. RESET so that the counter reading becomes "0:00:00". NOTE: You can also use REW ( ) or FF ( ), or JOG dial to locate the end point (See "Special Effect Playback": ੬ pg. 26) . EN 49 7 Locate start point Use REW ( ) or JOG dial to reverse the tape (See "Special Effect Playback": ੬ pg. 26). When you find the begining of the scene you want to edit, press PAUSE ( 8 ). 8 Activate editing mode Press INSERT on the front panel. ● Make sure that the recording format (VHS, SVHS or S-VHS ET) on the VCR is the same as that of the original recording on the tape. ● During Insert Editing pause mode ( , and light up on the front display panel.) ● For AV Dubbing, after pressing INSERT, press A.DUB also. During AV Dubbing insert pause mode ( and blink, and lights up on the front display panel.) 9 Start editing Press PLAY ( 3 ) on this VCR, and start playback on the other component at the same time. ● During Insert Editing mode ( and light up on the front display panel.) ● During AV Dubbing mode ( and blink on the front display panel.) ● When the counter reading becomes "0:00:00", editing automatically stops, and the VCR starts normal playback. To stop editing any time during recording Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel. NOTES: ● Be sure to select "AUTO" for "PICTURE CONTROL" (or "NORM" when "VIDEO CALIBRATION" is set to "OFF") after you finish editing the tapes (੬ pg. 37 and 38). ● Editing cannot be performed on a tape with its record safety tab removed. If you want to record onto a tape with its record safety tab removed, set "REC SAFETY" to "OFF" (੬ pg. 37, 41). ● The recording speed (SP/EP) is determined by the previous recording to be replaced. If the recording speed changes on the tape to be edited while editing the tape, the inserted picture will be distorted where the recording speed changes. ● When you edit a tape, a small portion of the recording preceding to the editing start point will be erased from the edited tape. ● "DAY/TIME INSERT" (੬ pg. 41) is not available during Insert Editing.