JVC SR-V10U SR-V10U Instruction manual (1MB, PDF) - Page 55

Timer Recording

Get JVC SR-V10U - S-vhs Hi-fi Stereo Videocassette Recorder PDF manuals and user guides View all JVC SR-V10U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

EN 55 TIMER RECORDING SYMPTOM 1. Timer recording will not work. 2. Timer programing will not work. 3. ‰ and ] on the front display panel will not stop blinking. 4. ‰ blinks for 10 seconds and the timer mode is disengaged. 5. The power shuts off and ‰ and ] will not stop blinking. 6. You moved, and now VCR Plus+ system does not work properly. 7. "PROGRAM FULL" is displayed on the screen. POSSIBLE CAUSE ● The clock and/or the timer have been set incorrectly. ● The timer is not engaged. ● The VCR has not been set up properly. ● Timer recording is in progress. ● The timer is engaged but there is no cassette loaded. ● "REC SAFETY" is set to "ON" and the loaded cassette has had its record safety tab removed. ● TIMER has been pressed when there are no programs in memory, or the timer recording program has not been set correctly. ● The tape reaches its end during timer recording. ● The receivable stations in the new area are received on different channels than those in the previous area. ● All 8 programs of the VCR's timer memory are used. CORRECTIVE ACTION Set the clock and/or timer correctly. Press TIMER and make sure that ‰ appears on the front display panel. Re-perform the set-up procedures. Make sure you have compensated for guide channel and VCR or cable box channel number mismatches (੬ pg. 30). Timer programing cannot be performed when timer recording is in progress. Wait until it finishes. Load a cassette with the record safety tab intact. If the tab is removed, set "REC SAFETY" to "OFF". (੬ pg. 37, 41) Set "REC SAFETY" to "OFF" (੬ pg. 37, 41) or replace the cassette with one on which the safety tab is intact. Check the programed data and set again if necessary, then press TIMER again. The program may not have been recorded in its entirety. Next time be sure you have enough time on the tape to record the entire broadcast. Re-perform the Changing VCR Plus+ Setting procedure (੬ pg. 30). Wait until a space in memory clears, or cancel unnecessary program information (੬ pg. 35). CONTINUED ON NEXT PAGE \

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
EN
55
CORRECTIVE ACTION
Set the clock and/or timer correctly.
Press
TIMER
and make sure that
‰
appears on the front display panel.
Re-perform the set-up procedures.
Make sure you have compensated for
guide channel and VCR or cable box
channel number mismatches
(
Z
pg. 30).
Timer programing cannot be performed
when timer recording is in progress.
Wait until it finishes.
Load a cassette with the record safety
tab intact. If the tab is removed, set
"REC SAFETY" to "OFF". (
Z
pg. 37,
41)
Set "REC SAFETY" to "OFF" (
Z
pg.
37, 41) or replace the cassette with
one on which the safety tab is intact.
Check the programed data and set
again if necessary, then press
TIMER
again.
The program may not have been
recorded in its entirety. Next time be
sure you have enough time on the
tape to record the entire broadcast.
Re-perform the Changing VCR Plus+
Setting procedure (
Z
pg. 30).
Wait until a space in memory clears,
or cancel unnecessary program
information (
Z
pg. 35).
SYMPTOM
1.
Timer recording will not work.
2.
Timer programing will not work.
3.
‰
and
]
on the front display
panel will not stop blinking.
4.
‰
blinks for 10 seconds and the
timer mode is disengaged.
5.
The power shuts off and
‰
and
]
will not stop blinking.
6.
You moved, and now VCR Plus+
system does not work properly.
7.
“PROGRAM FULL” is displayed on
the screen.
POSSIBLE CAUSE
●
The clock and/or the timer have
been set incorrectly.
●
The timer is not engaged.
●
The VCR has not been set up properly.
●
Timer recording is in progress.
●
The timer is engaged but there is no
cassette loaded.
●
"REC SAFETY" is set to "ON" and the
loaded cassette has had its record
safety tab removed.
●
TIMER
has been pressed when there
are no programs in memory, or the
timer recording program has not
been set correctly.
●
The tape reaches its end during
timer recording.
●
The receivable stations in the new
area are received on different
channels than those in the previous
area.
●
All 8 programs of the VCR’s timer
memory are used.
TIMER RECORDING
CONTINUED ON NEXT PAGE
\