Lexmark E260dn Service Manual - Page 64
-230, Error, Description, media detected during warm-up.
 |
View all Lexmark E260dn manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 64 highlights
4513-220, -230 Paper jam error codes (200-series) (Continued) Error Description 200.40 Invalid sample count in auto alignment. 200.41 ZW adder out of range in auto alignment. 200.42 Rogue sheet is at the manual feed sensor while flushing the paper path prior to declaring MPF source empty. 200.43 The paper is at the input sensor before interruption occurs. Possible causes include bouncy sensor or an exceptionally small gap, perhaps due to the paper being pre-staged in the source tray. 201.00 Paper jam between input and exit sensor 201.01 Transport motor identification failed to identify either motor after two tries. 201.02 Exit sensor never made by leading edge of page. Also known as internal jam. 201.03 Video never started on the page at the input sensor within two inches after hitting the input sensor 201.05 Restart attempted after an internal jam without the cover open/close event. It is likely that the jam was never cleared. 201.25 Exit sensor never made by leading edge of media when feeding out the media that was detected during warm- up. 201.26 Page at fuser nip before fuser started ramping toward desired temperature. Indicates code may be receiving more hall interrupts than intended 201.27 Page at fuser nip before fuser reached acceptable operating temperature. Page arrived at fuser earlier than expected, so it was probably staged 202.00 Paper jam around exit sensor. 202.01 Exit sensor never broke on the trailing edge of the sheet at the exit sensor. 202.02 Exit sensor never broke from sheet ahead of page heading toward the exit sensor. 202.06 Exit sensor bounced 202.13 Exit sensor covered, media not expected (media not in machine during warm-up) 202.25 Exit sensor never broke from the sheet ahead of the page heading toward the exit sensor when feeding out the media detected during warm-up. 202.26 Trailing edge never cleared exit sensor when feeding out media that was detected during warm-up. 202.32 Long media or shingled multi feed stopped before sending to duplex. 231.00 Duplex jam while reversing into the device 231.01 Duplex sensor never made by leading edge reversing into the duplex. 231.02 Bouncy duplex sensor never made. 232.00 Duplex jam while staging in the device 232.01 Duplex sensor never broke by the sheet ahead after reversing into the duplex. 232.02 Page in duplex ahead of current reversing page never staged. 233.00 Duplex jam while picking from the device 233.01 Page in duplex never picked. 233.02 Feed error picking from the duplex. 2-38 Lexmark™ E260d, E260dn
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59 -
60 -
61 -
62 -
63 -
64 -
65 -
66 -
67 -
68 -
69 -
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
 |
 |
