Lexmark Multifunction Laser C77x - Menus and Messages Guide - Page 27

Bin Setup, Duplex Bind

Get Lexmark Multifunction Laser PDF manuals and user guides View all Lexmark Multifunction Laser manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Using the MFP menus Menu item Portrait Height Feed Direction Purpose Values and descriptions Sets the portrait height of the universal media. Note: If the value set exceeds the maximum height, the MFP uses the maximum value allowed in inches or millimeters. 3-14.17 inches in 0.01 inch increments 76-360 mm in 1 mm increments Shows either inches or millimeters from the Units of Measure setting; 14 inches is the US default, and 356 mm is the international default. Specifies the feed direction of the Universal Paper Size. Short Edge* Long Edge Feed Direction is only shown if the Long Edge value is available. Long Edge exists if the longest edge is shorter than the maximum physical width that the tray can accommodate. See Duplex Bind on page 76 for more information about short and long edges. Bin Setup This menu item is used to specify the output bin where the printed print media goes. This menu item only appears if at least one optional output bin is installed, and only installed output bins appear as values. Menu item Output Bin Configure Bins Purpose Values and descriptions Specifies the default bin for printed print media. The number of bins listed are based on the number of bins installed. Standard Bin* Bin 1 Bin 2 Bin 3 Bin 4 Bin 5 Bin 6 Bin 7 Bin 8 Bin 9 Bin 10 Determines which output bin(s) Mailbox* the MFP uses for a particular job. Link Link Optional Mail Overflow Type Assignment If a user-defined name is available for an output bin, then the name appears instead. Note: If multiple output bins are assigned the same name, the name only appears once in the Output Bin value list. Sends print jobs to the output bin designated for that user. Links two or more output bins together as though they were one large bin. When one linked output bin is full, the MFP starts filling the next linked bin and continues with each additional linked bin. Note: The Link Optional value only appears when at least two optional output bins are installed. Sends print jobs to the output bin designated for the specific user until it is full, and then sends jobs to the designated overflow bin. Links all optional output bins as though they were one large bin, while leaving the standard output bin individually addressable. Paper Menu 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Paper Menu
27
Using the MFP menus
Bin Setup
This menu item is used to specify the output bin where the printed print media goes. This menu item only appears if at least
one optional output bin is installed, and only installed output bins appear as values.
Portrait Height
Sets the portrait height of the
universal media.
Note:
If the value set exceeds the
maximum height, the MFP uses the
maximum value allowed in inches or
millimeters.
3—14.17 inches in
0.01 inch increments
76—360 mm in 1 mm
increments
Shows either inches or millimeters
from the Units of Measure setting;
14 inches is the US default, and
356 mm is the international default.
Feed Direction
Specifies the feed direction of the
Universal Paper Size.
Short Edge*
Long Edge
Feed Direction is only shown if the
Long Edge value is available. Long
Edge exists if the longest edge is
shorter than the maximum physical
width that the tray can accommodate.
See
Duplex Bind on page 76
for
more information about short and long
edges.
Menu item
Purpose
Values and descriptions
Output Bin
Specifies the default bin for
printed print media.
The number of bins listed are
based on the number of bins
installed.
Standard Bin*
Bin 1
Bin 2
Bin 3
Bin 4
Bin 5
Bin 6
Bin 7
Bin 8
Bin 9
Bin 10
If a user-defined name is available
for an output bin, then the name
appears instead.
Note:
If multiple output bins are
assigned the same name, the
name only appears once in the
Output Bin value list.
Configure Bins
Determines which output bin(s)
the MFP uses for a particular
job.
Mailbox*
Sends print jobs to the output bin
designated for that user.
Link
Links two or more output bins
together as though they were one
large bin. When one linked output
bin is full, the MFP starts filling the
next linked bin and continues with
each additional linked bin.
Note:
The Link Optional value only
appears when at least two optional
output bins are installed.
Link Optional
Mail Overflow
Sends print jobs to the output bin
designated for the specific user
until it is full, and then sends jobs to
the designated overflow bin.
Type Assignment
Links all optional output bins as
though they were one large bin,
while leaving the standard output
bin individually addressable.
Menu item
Purpose
Values and descriptions