Lexmark Multifunction Laser C77x - Menus and Messages Guide - Page 38

Standard Parallel or Parallel <x

Get Lexmark Multifunction Laser PDF manuals and user guides View all Lexmark Multifunction Laser manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Using the MFP menus Standard Parallel or Parallel Use these menu items to change printer settings affecting jobs sent to the MFP through a parallel port, either Std Parallel or Parallel , where x represents 1 or 2. Menu item PCL SmartSwitch PS SmartSwitch NPA Mode Parallel Buffer Purpose Values and descriptions Configures the MFP so it On* automatically switches to PCL emulation when a print job received through the parallel port requires it, regardless of the default printer language. Off The MFP examines data on the parallel interface and selects PCL emulation if the data indicates that is the required printer language. The MFP does not examine the incoming data. The MFP uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off. Configures the MFP so it On* automatically switches to PostScript emulation when a print job received through the parallel port requires it, regardless of the default printer language. Off The MFP examines data on the parallel interface and selects PostScript emulation if the data indicates that is the required printer language. The MFP does not examine the incoming data. The MFP uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off. Specifies whether the MFP performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol. Note: Changing this menu item automatically resets the MFP. It is reset to configure memory, and any permanent resources, such as fonts or macros, are lost. On Off Auto* The MFP performs NPA processing. If data is not in NPA format, it is rejected as bad data. The MFP does not perform NPA processing. The MFP examines data, determines the format, and then processes it appropriately. Configures the size of the parallel input buffer. Note: Changing this menu item automatically resets the MFP. It is reset to configure memory, and any permanent resources, such as fonts or macros, are lost. Disabled Auto* Disables job buffering. Any jobs already buffered on the hard disk are printed before normal processing of incoming jobs resumes. The MFP automatically calculates the Parallel Buffer size (recommended setting). 3K to maximum size allowed (1K increments) The user specifies the Parallel Buffer size. The maximum size depends on the amount of memory in the MFP, the size of the other link buffers, and whether Resource Save is set to On or Off. To maximize the range for the Parallel Buffer size, disable or reduce the size of the serial and USB buffers. Network/Ports 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Network/Ports
38
Using the MFP menus
Standard Parallel or Parallel <x>
Use these menu items to change printer settings affecting jobs sent to the MFP through a parallel port, either Std Parallel or
Parallel <x>, where x represents 1 or 2.
Menu item
Purpose
Values and descriptions
PCL
SmartSwitch
Configures the MFP so it
automatically switches to
PCL emulation when a print job
received through the parallel port
requires it, regardless of the default
printer language.
On*
The MFP examines data on the
parallel interface and selects
PCL emulation if the data indicates
that is the required printer language.
Off
The MFP does not examine the
incoming data. The MFP uses
PostScript emulation to process the
job if PS SmartSwitch is On, or uses
the default printer language specified
in the
Setup
Menu
if PS SmartSwitch
is Off.
PS SmartSwitch
Configures the MFP so it
automatically switches to PostScript
emulation when a print job received
through the parallel port requires it,
regardless of the default printer
language.
On*
The MFP examines data on the
parallel interface and selects
PostScript emulation if the data
indicates that is the required printer
language.
Off
The MFP does not examine the
incoming data. The MFP uses PCL
emulation to process the job if PCL
SmartSwitch is On, or uses the default
printer language specified in the
Setup Menu
if PCL SmartSwitch is
Off.
NPA Mode
Specifies whether the MFP
performs the special processing
required for bidirectional
communication, following the
conventions defined in the Network
Printing Alliance (NPA) Protocol.
Note:
Changing this menu item
automatically resets the MFP. It is
reset to configure memory, and any
permanent resources, such as fonts
or macros, are lost.
On
The MFP performs NPA processing. If
data is not in NPA format, it is rejected
as bad data.
Off
The MFP does not perform NPA
processing.
Auto*
The MFP examines data, determines
the format, and then processes it
appropriately.
Parallel Buffer
Configures the size of the parallel
input buffer.
Note:
Changing this menu item
automatically resets the MFP. It is
reset to configure memory, and any
permanent resources, such as fonts
or macros, are lost.
Disabled
Disables job buffering. Any jobs
already buffered on the hard disk are
printed before normal processing of
incoming jobs resumes.
Auto*
The MFP automatically calculates the
Parallel Buffer size (recommended
setting).
3K to maximum
size allowed
(1K increments)
The user specifies the Parallel Buffer
size. The maximum size depends on
the amount of memory in the MFP, the
size of the other link buffers, and
whether Resource Save is set to On or
Off. To maximize the range for the
Parallel Buffer size, disable or reduce
the size of the serial and USB buffers.