Home » Netgear Manuals » Network Security & Firewall Devices » Netgear FVG318v1 » Manual Viewer

Netgear FVG318v1 FVG318 Reference Manual - Page 126

Table 7-1., FVG318 Status fields, This screen shows the following parameters

Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

ProSafe 802.11g Wireless VPN Firewall FVG318 Reference Manual This screen shows the following parameters: Table 7-1. FVG318 Status fields Field System Name Firmware Version Wireless Configuration SSID: Mode Security Settings Region Channel AP MAC Address WAN Port WAN State NAT DHCP Connection State IP Address IP Subnet Mask Gateway Primary DNS Secondary DNS DHCP MAC Address LAN Port MAC Address Description The System Name assigned to the firewall. The firewall firmware version. The wireless settings of the router The name of your wireless network. The default is NETGEAR. Shows what security has been associated with the wireless configuration. The default is none Shows the region is which the wireless gateway is operating Indicates the operating channel of the wireless radio. The MAC address of the wireless access point. These parameters apply to the Internet (WAN) port of the firewall. Indicates if the WAN port is up or down. Indicates if the router is in NAT mode (enabled) or in routing mode (disabled). The protocol on the WAN port used to obtain the WAN IP address. This field can show DHCP Client, Fixed IP, PPPoE, BPA or PPTP. For example, if set to Client, the firewall is configured to obtain an IP address dynamically from the ISP. Indicates if the WAN port is connected or not. The IP address used by the Internet (WAN) port of the firewall. If no address is shown, the firewall cannot connect to the Internet. The IP Subnet Mask being used by the Internet (WAN) port of the firewall. Gateway address of the WAN port. DNS server IP address of the WAN port. Secondary DNS server IP address of the WAN port (if not assigned, it will be the same as the primary DNS server). The protocol on the WAN port used to obtain the WAN IP address. This field can show DHCP Client, Fixed IP, PPPoE, BPA or PPTP. For example, if set to Client, the firewall is configured to obtain an IP address dynamically from the ISP. The MAC address used by the Internet (WAN) port of the firewall. These parameters apply to the Local (WAN) port of the firewall. The MAC address used by the LAN port of the firewall. 7-2 Maintenance v1.0, September 2007

Section	Page
ProSafe 802.11g Wireless VPN Firewall FVG318 Reference Manual	1
Contents	7
About This Manual	13
Conventions, Formats, and Scope	13
How to Use This Manual	14
How to Print this Manual	14
Revision History	15
Chapter 1 Introduction	17
Key Features of the VPN Firewall Router	17
802.11g and 802.11b Wireless Networking	18
Wireless Multimedia (WMM) Support	18
A Powerful, True Firewall with Content Filtering	18
Security	19
Autosensing Ethernet Connections with Auto Uplink	19
Extensive Protocol Support	19
Easy Installation and Management	20
Maintenance and Support	21
Package Contents	21
The FVG318 Front Panel	21
The FVG318 Rear Panel	22
Chapter 2 Connecting the Firewall to the Internet	25
Installing Your FVG318	25
Configuring the FVG318 for Internet Access with Auto Detect	28
Manually Configuring your Internet Connection	31
Configuring Dynamic DNS (If Needed)	33
Configuring Your Time Zone	35
Troubleshooting Tips	36
Be sure to restart your network in the correct sequence.	36
Make sure the Ethernet cables are securely plugged in.	36
Make sure the computer & router wireless settings match exactly.	36
Make sure the network settings of the computer are correct.	36
Check the router status lights to verify correct router operation.	37
Tips for Accessing the VPN firewall	37
Chapter 3 Configuring Wireless Connectivity	39
Observing Performance, Placement, and Range Guidelines	39
Implementing Appropriate Wireless Security	40
Understanding Wireless Settings	41
Security Check List for SSID and WEP Settings	45
Setting Up and Testing Basic Wireless Connectivity	46
Restricting Wireless Access by MAC Address	47
Configuring WEP Security Settings	48
Configuring WPA with RADIUS	50
Configuring WPA2 with RADIUS	52
Configuring WPA and WPA2 with RADIUS	53
Configuring WPA-PSK	55
Configuring WPA2-PSK	56
Configuring WPA-PSK and WPA2-PSK	58
Chapter 4 Firewall Protection and Content Filtering	61
Firewall Protection and Content Filtering Overview	61
Block Sites	61
Using Rules to Block or Allow Specific Kinds of Traffic	64
Inbound Rules (Port Forwarding)	66
Inbound Rule Example: A Local Public Web Server	67
Inbound Rule Example: Allowing a Videoconference from Restricted Addresses	67
Considerations for Inbound Rules	68
Outbound Rules (Service Blocking)	68
Outbound Rule Example: Blocking Instant Messenger	68
Order of Precedence for Rules	69
Default DMZ Server	70
Attack Checks	71
Services	72
Using a Schedule to Block or Allow Specific Traffic	73
Getting E-Mail Notifications of Firewall Logs	74
Chapter 5 Basic Virtual Private Networking	79
Overview of VPN Configuration	80
Client-to-Gateway VPN Tunnels	80
Gateway-to-Gateway VPN Tunnels	80
Planning a VPN	81
VPN Tunnel Configuration	82
Setting Up a Client-to-Gateway VPN Configuration	83
Step 1: Configuring the Client-to-Gateway VPN Tunnel on the FVG318	83
Step 2: Configuring the NETGEAR ProSafe VPN Client on the Remote PC	85
Monitoring the Progress and Status of the VPN Client Connection	93
Transferring a Security Policy to Another Client	95
Setting Up a Gateway-to-Gateway VPN Configuration	97
Activating a VPN Tunnel	101
Verifying the Status of a VPN Tunnel	103
Deactivating a VPN Tunnel	104
Using the Policy Table on the VPN Policies Screen to Deactivate a VPN Tunnel	104
Using the VPN Status Page to Deactivate a VPN Tunnel	105
Deleting a VPN Tunnel	105
Chapter 6 Advanced Virtual Private Networking	107
Using IKE and VPN Policies to Manage VPN Traffic	107
Using Automatic Key Management	108
IKE Policy Automatic Key and Authentication Management	108
VPN Policy Configuration for Auto Key and Manual Negotiation	109
Using Digital Certificates for IKE Auto-Policy Authentication	113
Certificate Revocation List (CRL)	113
VPN Configuration Scenarios on the FVG318	114
VPN Consortium Scenario 1: Gateway-to-Gateway with Preshared Secrets	115
FVG318 Gateway A to FVG318 Gateway B (IKE and VPN Policies)	116
Checking Your VPN Connections	119
VPN Consortium Scenario 2: FVG318 Gateway to Gateway with Digital Certificates	121
Chapter 7 Maintenance	125
Viewing VPN Firewall Router Status Information	125
Upgrading the Firewall Software	128
Backing Up and Restoring Settings	129
Changing the Administrator Password	130
Chapter 8 Advanced Configuration	131
Configuring Dynamic DNS	131
Using the LAN IP Setup Options	132
Configuring LAN TCP/IP Setup Parameters	132
Using the Firewall as a DHCP server	133
Using Address Reservation	134
Configuring Static Routes	135
Configuring RIP	136
Static Route Example	137
Enabling Remote Management Access	138
SNMP Administration	140
Enabling Universal Plug and Play (UPnP)	142
Chapter 9 Troubleshooting	143
Basic Functioning	143
Power LED Not On	143
LEDs Never Turn Off	144
LAN or Internet Port LEDs Not On	144
Troubleshooting the Web Configuration Interface	144
Troubleshooting the ISP Connection	145
Troubleshooting a TCP/IP Network Using a Ping Utility	147
Testing the LAN Path to Your Firewall	147
Testing the Path from Your PC to a Remote Device	148
Restoring the Default Configuration and Password	148
Problems with Date and Time	149
Appendix A Default Settings and Technical Specifications	151
Default Settings	151
Technical Specifications	153
Appendix B Related Documents	155
Appendix C VPN Configuration of NETGEAR FVG318	157
Case Study Overview	157
Gathering the Network Information	157
Configuring the Gateways	158
Activating the VPN Tunnel	159
The FVG318-to-FVG318 Case	159
Configuring the VPN Tunnel	160
Viewing and Editing the VPN Parameters	161
Initiating and Checking the VPN Connections	162
The FVG318-to-FVS318v2 Case	163
Configuring the VPN Tunnel	163
Viewing and Editing the VPN Parameters	164
Initiating and Checking the VPN Connections	165
The FVG318-to-FVL328 Case	166
Configuring the VPN Tunnel	166
Viewing and Editing the VPN Parameters	167
Initiating and Checking the VPN Connections	168
The FVG318-to-VPN Client Case	169
Client-to-Gateway VPN Tunnel Overview	169
Configuring the VPN Tunnel	170

Match case Limit results 1 per page

ProSafe 802.11g Wireless VPN Firewall FVG318 Reference Manual

7-2

Maintenance

v1.0, September 2007

This screen shows the following parameters:

Table 7-1.

FVG318 Status fields

Field

Description

System Name

The System Name assigned to the firewall.

Firmware Version

The firewall firmware version.

Wireless Configuration

The wireless settings of the router

SSID:

The name of your wireless network. The default is NETGEAR.

Mode

Security Settings

Shows what security has been associated with the wireless configuration. The

default is none

Region

Shows the region is which the wireless gateway is operating

Channel

Indicates the operating channel of the wireless radio.

AP MAC Address

The MAC address of the wireless access point.

WAN Port

These parameters apply to the Internet (WAN) port of the firewall.

WAN State

Indicates if the WAN port is up or down.

NAT

Indicates if the router is in NAT mode (enabled) or in routing mode (disabled).

DHCP

The protocol on the WAN port used to obtain the WAN IP address. This field

can show DHCP Client, Fixed IP, PPPoE, BPA or PPTP. For example, if set to

Client, the firewall is configured to obtain an IP address dynamically from the

ISP.

Connection State

Indicates if the WAN port is connected or not.

IP Address

The IP address used by the Internet (WAN) port of the firewall. If no address is

shown, the firewall cannot connect to the Internet.

IP Subnet Mask

The IP Subnet Mask being used by the Internet (WAN) port of the firewall.

Gateway

Gateway address of the WAN port.

Primary DNS

DNS server IP address of the WAN port.

Secondary DNS

Secondary DNS server IP address of the WAN port (if not assigned, it will be

the same as the primary DNS server).

DHCP

The protocol on the WAN port used to obtain the WAN IP address. This field

can show DHCP Client, Fixed IP, PPPoE, BPA or PPTP. For example, if set to

Client, the firewall is configured to obtain an IP address dynamically from the

ISP.

MAC Address

The MAC address used by the Internet (WAN) port of the firewall.

LAN Port

These parameters apply to the Local (WAN) port of the firewall.

MAC Address

The MAC address used by the LAN port of the firewall.