Netgear GSM7312 FSM7326P User Manual - Page 120

config users snmpv3 accessmode, show loginsession, config loginsession close, Security Commands

Page 120 highlights

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software config users snmpv3 accessmode This command specifies the snmpv3 access privileges for the specified login user. The valid accessmode values are readonly or readwrite. The is the login user name for which the specified access mode will apply. Default Format readwrite for admin user; readonly for all other users config users snmpv3 accessmode show loginsession This command displays current telnet and serial port connections to the switch. Format ID User Name Connection From Idle Time Session Time show loginsession Login Session ID. The name the user will use to login using the serial port or Telnet. A new user may be added to the switch by entering a name in a blank entry. The user name may be up to 8 characters, and is not case sensitive. Two users are included as the factory default, admin and guest. IP address of the telnet client machine or EIA-232 for the serial port connection. Time this session has been idle. Total time this session has been connected. config loginsession close This command closes a telnet session. Format config loginsession close Security Commands This section describes commands used for configuring security settings for login users and port users. This command permanently saves configuration changes to Non-Volatile Random Access Memory (NVRAM). Format save config 7-58 202-10009-01 Switching Commands

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software
7-58
Switching Commands
202-10009-01
config users snmpv3 accessmode
This command specifies the snmpv3 access privileges for the specified login user. The valid
accessmode values are
readonly
or
readwrite
. The
<user>
is the login user name for which the
specified access mode will apply.
Default
readwrite
for admin user;
readonly
for all other users
Format
config users snmpv3 accessmode <user> <readonly/
readwrite>
show loginsession
This command displays current telnet and serial port connections to the switch.
Format
show loginsession
ID
Login Session ID.
User Name
The name the user will use to login using the serial port or Telnet. A new user
may be added to the switch by entering a name in a blank entry. The user name
may be up to 8 characters, and is not case sensitive. Two users are included as
the factory default, admin and guest.
Connection From
IP address of the telnet client machine or EIA-232 for the serial port connection.
Idle Time
Time this session has been idle.
Session Time
Total time this session has been connected.
config loginsession close
This command closes a telnet session.
Format
config loginsession close
<sessionID/all>
Security Commands
This section describes commands used for configuring security settings for login users and port
users.
This command permanently saves configuration changes to Non-Volatile Random Access
Memory (NVRAM).
Format
save config