Netgear GSM7312 FSM7326P User Manual - Page 49

Quick Startup, Quick Starting the Switch

Page 49 highlights

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Chapter 6 Quick Startup The Command Line Interface (CLI) Quick Startup chapter details procedures to quickly become acquainted with the 7000 Series L3 Managed Switch Software. This chapter contains the following Quick Startup examples: • "System Info and System Setup" on page 6-2 • "Configuration Examples" on page 6-8 • "VLAN Example" on page 6-12 Quick Starting the Switch 1. Read the device Installation Guide for the connectivity procedure. In-band connectivity allows access to the 7000 Series L3 Managed Switch Software locally or from a remote workstation. The device must be configured with IP information (IP address, subnet mask, and default gateway). 2. Allow the device to load the software until the login prompt appears. The device initial state is called the default mode. 3. When the prompt asks for operator login, execute the following steps: • Type the word admin in the login area. Since a number of the Quick Setup commands require administrator account rights, log in using an administrator account. • Do not enter a password because there is no password in the default mode. • Press the enter key two times. Quick Startup 6-1 202-10009-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software
Quick Startup
6-1
202-10009-01
Chapter 6
Quick Startup
The Command Line Interface (CLI) Quick Startup chapter details procedures to quickly become
acquainted with the 7000 Series L3 Managed Switch Software.
This chapter contains the following Quick Startup examples:
“System Info and System Setup” on page 6-2
“Configuration Examples” on page 6-8
“VLAN Example” on page 6-12
Quick Starting the Switch
1.
Read the device Installation Guide for the connectivity procedure. In-band connectivity allows
access to the 7000 Series L3 Managed Switch Software locally or from a remote workstation.
The device must be configured with IP information (IP address, subnet mask, and default
gateway).
2.
Allow the device to load the software until the login prompt appears. The device initial state is
called the default mode.
3.
When the prompt asks for operator login, execute the following steps:
Type the word
admin
in the login area. Since a number of the Quick Setup commands
require administrator account rights, log in using an administrator account.
Do not enter a password because there is no password in the default mode.
Press the enter key two times.