Netgear GSM7312 FSM7326P User Manual - Page 137

transfer upload serverip, transfer upload path, TFTP Upload Example.

Page 137 highlights

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software Format transfer upload mode transfer upload serverip This command sets the IP address of the server on which the file is located. Note: This command is valid only when the transfer mode is TFTP. See "transfer upload mode" . Default 0.0.0.0 Format transfer upload serverip transfer upload path This command sets the directory path used to upload the file. The switch "remembers" the last file path used. Note: This command is valid only when the transfer mode is TFTP. See "transfer upload mode" . NETGEAR 7300 Series Layer 3 Managed Switch software supports the TFTP client. The TFTP client path statement requirement is sever dependent. A path statement is generally required to set up the TFTP client; however, the client path may remain blank. See the example of the path setup. TFTP Upload Example: The TFTP upload example details three scenarios for TFTP client to server file transfer. In the example, the operator will upload the config.bin file from the switch to the location c:\tftp\ on the server. The different scenarios are detailed below: Table 3. TFTP Upload Example. TFTP Server path c:\tftp\ c:\ c: TFTP Client path blank tftp\ \tftp\ NETGEAR 7300 Series Layer 3 Managed Switch software provides two methods to clear the directory path statement. • The clear config command will remove the directory path statement. • The web browser clear command will remove the directory path statement. Default Format Blank transfer upload path Switching Commands 202-10009-01 7-75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software
Switching Commands
7-75
202-10009-01
Format
transfer upload mode
<xmodem|tftp>
transfer upload serverip
This command sets the IP address of the server on which the file is located.
Note:
This command is valid only when the transfer mode is TFTP. See “transfer upload mode” .
Default
0.0.0.0
Format
transfer upload serverip
<ipaddr>
transfer upload path
This command sets the directory path used to upload the file. The switch “remembers” the last file
path used.
Note:
This command is valid only when the transfer mode is TFTP. See “transfer upload mode” .
NETGEAR 7300 Series Layer 3 Managed Switch software supports the TFTP client. The TFTP
client path statement requirement is sever dependent. A path statement is generally required to set
up the TFTP client; however, the client path may remain blank.
See the example of the path setup.
TFTP Upload Example:
The TFTP upload example details three scenarios for TFTP client to server file
transfer.
In the example, the operator will upload the config.bin file from the switch to
the location c:\tftp\ on the server. The different scenarios are detailed below:
NETGEAR 7300 Series Layer 3 Managed Switch software provides two methods to clear the
directory path statement.
The
clear config
command will remove the directory path statement.
The web browser clear command will remove the directory path statement.
Default
Blank
Format
transfer upload path
<path>
Table 3.
TFTP Upload Example.
TFTP Server path
TFTP Client path
c:\tftp\
blank
c:\
tftp\
c:
\tftp\