Netgear GSM7312 FSM7326P User Manual - Page 156

config router rip interface version send, OSPF Commands, show router ospf info

Page 156 highlights

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software The value for is a valid routing slot and port number or all for selecting every routing port. The value for is one of: rip1 to receive only RIP version 1 formatted packets, rip2 for RIP version 2, both to receive packets from either format, or none to not allow any RIP control packets to be received. Default Format both config router rip interface version receive config router rip interface version send This command configures the interface to allow RIP control packets of the specified version to be sent. The value for is a valid routing slot and port number or all for selecting every routing port. The value for is one of: rip1 to broadcast RIP version 1 formatted packets, rip1c (RIP version 1 compatibility mode) which sends RIP version 2 formatted packets via broadcast, rip2 for sending RIP version 2 using multicast, or none to not allow any RIP control packets to be sent. Default Format rip1c config router rip interface version send OSPF Commands show router ospf info This command displays information relevant to the OSPF router. This command takes no options. Format Router ID OSPF Admin Mode ASBR Mode show router ospf info A 32 bit integer in dotted decimal format identifying the router, about which information is displayed. This is a configured value. The administrative mode of OSPF in the router. This is a configured value. Reflects whether the ASBR mode is enabled or disabled. Enable implies that the router is an autonomous system border router. This is a configured value. The information below will only be displayed if OSPF is enabled. ABR Status Reflects the whether or not the router is an OSPF Area Border Router. 8-14 202-10009-01 Routing Commands

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software
8-14
Routing Commands
202-10009-01
The value for <slot.port> is a valid routing slot and port number or all for selecting every routing
port.
The value for <mode> is one of: rip1 to receive only RIP version 1 formatted packets, rip2 for RIP
version 2, both to receive packets from either format, or none to not allow any RIP control packets
to be received.
Default
both
Format
config router rip interface version receive
<slot.port> <rip1|rip2|both|none>
config router rip interface version send
This command configures the interface to allow RIP control packets of the specified version to be
sent. The value for <slot.port> is a valid routing slot and port number or all for selecting every
routing port.
The value for <mode> is one of: rip1 to broadcast RIP version 1 formatted packets, rip1c (RIP
version 1 compatibility mode) which sends RIP version 2 formatted packets via broadcast, rip2 for
sending RIP version 2 using multicast, or none to not allow any RIP control packets to be sent.
Default
rip1c
Format
config router rip interface version send
<slot.port>
<rip1|rip1c|rip2|none>
OSPF Commands
show router ospf info
This command displays information relevant to the OSPF router. This command takes no options.
Format
show router ospf info
Router ID
A 32 bit integer in dotted decimal format identifying the router, about which
information is displayed. This is a configured value.
OSPF Admin Mode
The administrative mode of OSPF in the router. This is a configured value.
ASBR Mode
Reflects whether the ASBR mode is enabled or disabled. Enable implies that the
router is an autonomous system border router. This is a configured value.
The information below will only be displayed if OSPF is enabled.
ABR Status
Reflects the whether or not the router is an OSPF Area Border Router.