Netgear GSM7312 FSM7326P User Manual - Page 147

config router route default create, ARP Commands, show arp table

Page 147 highlights

Format User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software config router route preference config router route default create This command configures the default route. The value for is a valid IP address of the next hop router. Format config router route default create config router route default delete This command causes the static default route to be deleted. Format config router route default delete ARP Commands show arp table This command displays the Address Resolution Protocol (ARP) cache. The displayed results are not the total ARP entries. To view the total ARP entries, the operator should view the show arp table results in conjunction with the show arp switch results. Format Age Time (seconds) Response Time (seconds) Retries Cache Size IP Address MAC Address Interface Type show arp table The time it takes for an ARP entry to age out. This value was configured into the unit. Age time is measured in seconds. The time it takes for an ARP request timeout. This value was configured into the unit. Response time is measured in seconds. The maximum number of times an ARP request is retried. This value was configured into the unit. The maximum number of entries in the ARP table. This value was configured into the unit. The IP assigned to each interface. The hardware MAC address that each interface maps to. The associated slot.port which identifies an ARP entry. The type that was configured into the unit. The possible values are Local, Gateway, Dynamic and Static. Routing Commands 8-5 202-10009-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software
Routing Commands
8-5
202-10009-01
Format
config router route preference
<local/static> <0-255>
config router route default create
This command configures the default route. The value for <nexthopip> is a valid IP address of the
next hop router.
Format
config router route default create
<nexthopip>
config router route default delete
This command causes the static default route to be deleted.
Format
config router route default delete
ARP Commands
show arp table
This command displays the Address Resolution Protocol (ARP) cache. The displayed results are
not the total ARP entries. To view the total ARP entries, the operator should view the
show arp
table
results in conjunction with the
show arp switch
results.
Format
show arp table
Age Time (seconds)
The time it takes for an ARP entry to age out. This value was configured into the
unit. Age time is measured in seconds.
Response Time (seconds)
The time it takes for an ARP request timeout. This value was configured into the
unit. Response time is measured in seconds.
Retries
The maximum number of times an ARP request is retried. This value was
configured into the unit.
Cache Size
The maximum number of entries in the ARP table. This value was configured
into the unit.
IP Address
The IP assigned to each interface.
MAC Address
The hardware MAC address that each interface maps to.
Interface
The associated slot.port which identifies an ARP entry.
Type
The type that was configured into the unit. The possible values are Local,
Gateway, Dynamic and Static.