Netgear GSM7312 FSM7326P User Manual - Page 78

config serial baudrate, config serial timeout, show serviceport, config serviceport parms, Default

Page 78 highlights

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software config serial baudrate This command specifies the communication rate of the terminal interface. The supported rates are 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200. Default Format 9600 config serial baudrate config serial timeout This command specifies the maximum connect time (in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely. The time range is 0 to 160. Default Format 5 config serial timeout show serviceport This command displays service port configuration information. Format IP Address Subnet Mask Default Gateway ServPort Configuration Protocol Current Burnedin MAC Address show serviceport The IP address of the interface. The factory default value is 0.0.0.0 The IP subnet mask for this interface. The factory default value is 0.0.0.0 The default gateway for this IP interface. The factory default value is 0.0.0.0 Indicates what network protocol was used on the last, or current power-up cycle, if any. The burnedin MAC address used for in-band connectivity. config serviceport parms This command sets the IP address, the netmask and the gateway of the router. Format config serviceport parms [gateway] config serviceport protocol This command specifies the servicePort configuration protocol. If you modify this value, the change takes effect immediately. Format config serviceport protocol 7-16 202-10009-01 Switching Commands

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software
7-16
Switching Commands
202-10009-01
config serial baudrate
This command specifies the communication rate of the terminal interface. The supported rates are
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200.
Default
9600
Format
config serial baudrate
<speed>
config serial timeout
This command specifies the maximum connect time (in minutes) without console activity. A value
of 0 indicates that a console can be connected indefinitely. The time range is 0 to 160.
Default
5
Format
config serial timeout <
0 - 160
>
show serviceport
This command displays service port configuration information.
Format
show serviceport
IP Address
The IP address of the interface. The factory default value is 0.0.0.0
Subnet Mask
The IP subnet mask for this interface. The factory default value is 0.0.0.0
Default Gateway
The default gateway for this IP interface. The factory default value is 0.0.0.0
ServPort Configuration
Protocol Current
Indicates what network protocol was used on the last, or current power-up cycle,
if any.
Burnedin MAC Address
The burnedin MAC address used for in-band connectivity.
config serviceport parms
This command sets the IP address, the netmask and the gateway of the router.
Format
config serviceport parms
<
ipAddr
>
<netmask> [gateway]
config serviceport protocol
This command specifies the servicePort configuration protocol. If you modify this value, the
change takes effect immediately.
Format
config serviceport protocol
<none|bootp|dhcp>