Netgear GSM7312 FSM7326P User Manual - Page 88

config port linktrap, config port physicalmode, show lag

Page 88 highlights

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software config port linktrap This command enables or disables link status traps by interface. Note: This command is valid only when the Link Up/Down Flag is enabled. See "config trapflags linkmode" on page 21 for more information. Format config port linktrap < slot.port|all> config port physicalmode This command sets the speed and duplex setting for the interface. Format config port physicalmode Acceptable values are: 100h 100f 10h 10f 100BASE-T half-duplex 100BASE-T full duplex 10BASE-T half duplex 100BASE-T full duplex config port lacpmode This command enables or disables Link Aggregation Control Protocol (LACP) on a port. The possible values for are enable and disable. The default value is disable. Format config port lacpmode config port autoneg This command enables or disables automatic negotiation on a port. The possible values for are enable and disable. The default value is enable. Format config port autoneg show lag This command displays an overview of all link aggregations (LAGs) on the switch. Format show lag 7-26 202-10009-01 Switching Commands

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268

User Manual for the NETGEAR 7300 Series Layer 3 Managed Switch Software
7-26
Switching Commands
202-10009-01
config port linktrap
This command enables or disables link status traps by interface.
Note:
This command is valid only when the Link Up/Down Flag is enabled. See “config trapflags
linkmode” on page 21 for more information.
Format
config port linktrap
< slot.port|all>
<enable|disable>
config port physicalmode
This command sets the speed and duplex setting for the interface.
Format
config port physicalmode
<slot.port|all>
<100h|100f|10h|10f>
Acceptable values are:
100h
100BASE-T half-duplex
100f
100BASE-T full duplex
10h
10BASE-T half duplex
10f
100BASE-T full duplex
config port lacpmode
This command enables or disables Link Aggregation Control Protocol (LACP) on a port. The
possible values for <mode> are enable and disable. The default value is disable.
Format
config port lacpmode <slot.port/all> <enable/disable>
config port autoneg
This command enables or disables automatic negotiation on a port. The possible values for
<mode> are enable and disable. The default value is enable.
Format
config port autoneg <slot.port/all> <enable/disable>
show lag
This command displays an overview of all link aggregations (LAGs) on the switch.
Format
show lag <logical slot.port|all>