Ricoh D7500 Operating Instructions 4 - Page 87

Interactive Whiteboard D8600 and, the Interactive Whiteboard.

Get Ricoh D7500 PDF manuals and user guides View all Ricoh D7500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

If a Message is Displayed during Operation Message Causes Solutions A communication failure has occurred. Save the created page and restart the application. • A timeout occurred while you were opening a whiteboard session. • An internal error occurred while you were using remote whiteboard. Save the page as needed. Next, quickly press and release the power button of the machine. When the Interactive Whiteboard is turned off, press the power button again to restart the Interactive Whiteboard. When you are using the RICOH Interactive Whiteboard D8600 and [For standby press the power button] is enabled, press and hold the power button to shut down the machine while the whiteboard screen is displayed. A communication timeout has occurred. Possible causes may be as follows. - Not connected to the network - A failure has occurred on the host terminal • The network cable is not connected or is broken. • The network bandwidth is too low. • The host device is having a problem. • Check that the network cable is connected or is not broken. • Check the network band width. • Check the network settings of the whiteboard, and then configure the IP address of it. Cannot participate in remote The specified host name is whiteboard because the host incorrect. name has not been found Check the specified host name and enter the host name again. Cannot continue remote whiteboard because of a communication error The following are possible causes. - The network settings are incorrect - The network cable is not connected Check the network status and then try again. • The network cable is not connected. • The IP address is not set. • No IP address can be obtained over DHCP. • The IP address of the host whiteboard is incorrect. Check the network status and open the session again. 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Message
Causes
Solutions
A communication failure has
occurred.
Save the created page and
restart the application.
•
A timeout occurred
while you were
opening a whiteboard
session.
•
An internal error
occurred while you
were using remote
whiteboard.
Save the page as needed. Next,
quickly press and release the power
button of the machine. When the
Interactive Whiteboard is turned off,
press the power button again to restart
the Interactive Whiteboard.
When you are using the RICOH
Interactive Whiteboard D8600 and
[For standby press the power button] is
enabled, press and hold the power
button to shut down the machine while
the whiteboard screen is displayed.
A communication timeout
has occurred.
Possible causes may be as
follows.
- Not connected to the
network
- A failure has occurred on
the host terminal
•
The network cable is
not connected or is
broken.
•
The network bandwidth
is too low.
•
The host device is
having a problem.
•
Check that the network cable is
connected or is not broken.
•
Check the network band width.
•
Check the network settings of the
whiteboard, and then configure
the IP address of it.
Cannot participate in remote
whiteboard because the host
name has not been found
The specified host name is
incorrect.
Check the specified host name and
enter the host name again.
Cannot continue remote
whiteboard because of a
communication error
The following are possible
causes.
- The network settings are
incorrect
- The network cable is not
connected
Check the network status
and then try again.
•
The network cable is
not connected.
•
The IP address is not
set.
•
No IP address can be
obtained over DHCP.
•
The IP address of the
host whiteboard is
incorrect.
Check the network status and open the
session again.
If a Message is Displayed during Operation
85