Sony MZ-N1 Operating Instructions - Page 21

To stop recording, flip the control bar towards, To cancel synchro-recording

Get Sony MZ-N1 PDF manuals and user guides View all Sony MZ-N1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

To stop recording, flip the control bar towards x. After you flip the bar towards x to stop, the recorder will automatically turn off in about 10 seconds (when using batteries) or about 3 minutes (when using AC power adaptor). To cancel synchro-recording Turn the jog dial until "SYNC OFF" flashes in the display in step 3, and then press to enter. Note If you record on a previously recorded disc, the recorder is factory set to overwrite the entire contents of the disc. If you want the recording to start after the existing contents, do the procedure "Recording without overwriting existing material" (page 33) before doing step 3, "Record an MD." (page 20). To Press Record from the end of the current contents1) If "REC-Posi" (the record-starting position setting) is set to "From Here", press END SEARCH, and then press and slide REC to the right.1) If "REC-Posi" is set to "From End", press and slide REC to the right. Record over partway through the previous recording1) Press N, ., or > to find the start point of recording and flip the bar towards x to stop. Then press and slide REC to the right. Pause Flip the bar towards X2). Flip the bar towards X again to resume recording. Remove the MD Flip the bar towards x and open the lid.3) (The lid does not open while "TOC Edit" flashing in the display.) 1) If "REC-Posi" is set to "From End", recording operations will always start from the end of the previously recorded material without pressing the END SEARCH button (page 33). 2) A track mark is added at the point where you flip the bar towards X again to resume recording while pausing; thus the remainder of the track will be counted as a new track. 3) If you open the lid while "REC-Posi" is set to "From Here", recording will begin from the top of the disc the next time you record. Check the point to start recording on the display. If the recording does not start • Make sure the recorder is not locked (pages 17, 72). • Make sure the MD is not record-protected (pages 19, 75). • Premastered MDs cannot be recorded over. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
21
To stop recording, flip the control bar towards
x
.
After you flip the bar towards
x
to stop, the recorder will automatically turn off in about 10 seconds
(when using batteries) or about 3 minutes (when using AC power adaptor).
To cancel synchro-recording
Turn the jog dial until
“
SYNC OFF
”
flashes in the display in step
3
, and then press to enter.
Note
If you record on a previously recorded disc, the recorder is factory set to overwrite the
entire contents of the disc. If you want the recording to start after the existing contents,
do the procedure
“
Recording without overwriting existing material
”
(page 33) before
doing step 3,
“
Record an MD.
”
(page 20).
If the recording does not start
•
Make sure the recorder is not locked (pages
17, 72).
•
Make sure the MD is not record-protected
(pages 19, 75).
•
Premastered MDs cannot be recorded over.
To
Press
Record from the end of
the current contents
1)
1)
If
“
REC-Posi
”
is set to
“
From End
”
, recording operations will always start from the end of the
previously recorded material without pressing the END SEARCH button (page 33).
If
“
REC-Posi
”
(the record-starting position setting) is set to
“
From Here
”
, press END SEARCH, and then press and slide
REC to the right.
1)
If
“
REC-Posi
”
is set to
“
From End
”
, press and slide REC to the
right.
Record over partway
through the previous
recording
1)
Press
N
,
.
, or
>
to find the start point of recording and
flip the bar towards
x
to stop.
Then press and slide REC to the right.
Pause
Flip the bar towards
X
2)
.
Flip the bar towards
X
again to resume recording.
2)
A track mark is added at the point where you flip the bar towards
X
again to resume recording while
pausing; thus the remainder of the track will be counted as a new track.
Remove the MD
Flip the bar towards
x
and open the lid.
3)
(The lid does not open
while
“
TOC Edit
”
flashing in the display.)
3)
If you open the lid while
“
REC-Posi
”
is set to
“
From Here
”
, recording will begin from the top of the
disc the next time you record. Check the point to start recording on the display.