Sony MZ-N1 Operating Instructions - Page 90

Messages, Error message, Meaning/Remedy

Get Sony MZ-N1 PDF manuals and user guides View all Sony MZ-N1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Messages If the following error messages flash in the display window, check the chart below. Error message Meaning/Remedy BANK FULL • The character stored in the phrase bank has reached to 400. , Delete some phrases from the name bank, and then reenter the new phrase. BLANKDISC • An MD with no recording on it is inserted. BUSY • You tried to operate the recorder while it was accessing the recorded data. , Wait until the message goes out (in rare cases, it may take a few minutes). Data Save • The MD player is recording information (sounds) from the memory to the disc. , Wait until this process is completed. Do not expose the player to any physical shock, nor disrupt power supply. DISC FULL EMPTY • The remaining recording time on the disc is 12 seconds (SP stereo), 24 seconds (LP2 stereo or monaural), 36 seconds (LP4 stereo), or less. , Replace the disc. • You tried to erase data in the name bank but no data have been recorded. Hi DC in • Voltage of the power supply is too high (The supplied AC power adaptor or the recommended car battery cord is not used). , Use the supplied AC power adaptor or the recommended car battery cord. HOLD • The recorder is locked. , Slide HOLD against the arrow to unlock the recorder (page 72). LINE OUT • You pressed VOLUME +/- while the "AUDIO OUT" parameter was set to "LINE OUT." , Use the jog dial to set the "AUDIO OUT" parameter to "HeadPhone" (page 27). LOW BATT • Batteries are weak. , Charge the rechargeable battery or replace the dry battery (page 73). MEM OVER MENU • You tried to record with the recorder placed where it receives continuous vibration. , Put the recorder on a stable place, and start recording again. • You pressed a key on the remote control while selecting a menu on the recorder. You pressed a key on the recorder while selecting a menu on the remote control. 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
90
Messages
If the following error messages flash in the display window, check the chart below.
Error message
Meaning/Remedy
BANK FULL
•
The character stored in the phrase bank has reached to 400.
,
Delete some phrases from the name bank, and then reenter the
new phrase.
BLANKDISC
•
An MD with no recording on it is inserted.
BUSY
•
You tried to operate the recorder while it was accessing the
recorded data.
,
Wait until the message goes out (in rare cases, it may take a
few minutes).
Data Save
•
The MD player is recording information (sounds) from the
memory to the disc.
,
Wait until this process is completed. Do not expose the player
to any physical shock, nor disrupt power supply.
DISC FULL
•
The remaining recording time on the disc is 12 seconds (SP
stereo), 24 seconds (LP2 stereo or monaural), 36 seconds (LP4
stereo), or less.
,
Replace the disc.
EMPTY
•
You tried to erase data in the name bank but no data have been
recorded.
Hi DC in
•
Voltage of the power supply is too high (The supplied AC power
adaptor or the recommended car battery cord is not used).
,
Use the supplied AC power adaptor or the recommended car
battery cord.
HOLD
•
The recorder is locked.
,
Slide HOLD against the arrow to unlock the recorder
(page 72).
LINE OUT
•
You pressed VOLUME +/
–
while the
“
AUDIO OUT
”
parameter
was set to
“
LINE OUT.
”
,
Use the jog dial to set the
“
AUDIO OUT
”
parameter to
“
HeadPhone
”
(page 27).
LOW BATT
•
Batteries are weak.
,
Charge the rechargeable battery or replace the dry battery
(page 73).
MEM OVER
•
You tried to record with the recorder placed where it receives
continuous vibration.
,
Put the recorder on a stable place, and start recording again.
MENU
•
You pressed a key on the remote control while selecting a menu on
the recorder. You pressed a key on the recorder while selecting a
menu on the remote control.