Yamaha RX V659 MCXSP10 Manual - Page 115

TROUBLESHOOTING, General - problem

Get Yamaha RX V659 - AV Receiver PDF manuals and user guides
UPC - 027108925295
View all Yamaha RX V659 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

TROUBLESHOOTING TROUBLESHOOTING Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized YAMAHA dealer or service center. ■ General Problem Cause Remedy This unit fails to turn on or enters the standby mode soon after the power is turned on. No sound No picture The power cable is not connected or the plug is not completely inserted. The speaker impedance setting is incorrect. The protection circuitry has been activated. This unit has been exposed to a strong external electric shock (such as lightning or strong static electricity). Incorrect input or output cable connections. "INPUT MODE" is set to "DTS" or "ANALOG". No appropriate input source has been selected. Speaker connections are not secure. The front speakers to be used have not been selected properly. The volume is turned down. The sound is muted. "INPUT MODE" is set to "ANALOG" while playing a source encoded in DTS. Signals this unit cannot reproduce are being input from a source component, such as a CD-ROM. The output and input for the picture are connected to different types of video jacks. Connect the power cable firmly. Set the speaker impedance to match your speakers. Make sure that all speaker wire connections on this unit and on all speakers are secure and that the wire for each connection does not touch anything other than its respective connection. Set this unit to the standby mode, disconnect the power cable, plug it back in after 30 seconds and then use it normally. Connect the cables properly. If the problem persists, the cables may be defective. Set "INPUT MODE" to "AUTO". Select an appropriate input source with the INPUT selector on the front panel (or the input selector buttons on the remote control) and MULTI CH INPUT on the front panel (or MULTI CH IN on the remote control). Secure the connections. Select the front speakers with SPEAKERS A and/or B on the front panel or SPEAKERS on the remote control. Turn up the volume. Press MUTE or VOLUME +/- on the remote control to resume audio output and then adjust the volume. Set "INPUT MODE" to "AUTO" or "DTS". Play a source whose signals can be reproduced by this unit. Set "VIDEO CONV." to "ON". See page - 30 13 - 19-27 41 38, 44 13 38 - 40 41 - 94 ADDITIONAL INFORMATION 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
TROUBLESHOOTING
111
ADDITIONAL
INFORMATION
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
YAMAHA dealer or service center.
■
General
TROUBLESHOOTING
Problem
Cause
Remedy
See
page
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
—
The speaker impedance setting is
incorrect.
Set the speaker impedance to match your speakers.
30
The protection circuitry has been
activated.
Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wire
for each connection does not touch anything other
than its respective connection.
13
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and then
use it normally.
—
No sound
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
19-27
“INPUT MODE” is set to “DTS” or
“ANALOG”.
Set “INPUT MODE” to “AUTO”.
41
No appropriate input source has been
selected.
Select an appropriate input source with the INPUT
selector on the front panel (or the input selector
buttons on the remote control) and MULTI CH
INPUT on the front panel (or MULTI CH IN on the
remote control).
38, 44
Speaker connections are not secure.
Secure the connections.
13
The front speakers to be used have not
been selected properly.
Select the front speakers with SPEAKERS A and/or
B on the front panel or SPEAKERS on the remote
control.
38
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press MUTE or VOLUME +/– on the remote control
to resume audio output and then adjust the volume.
40
“INPUT MODE” is set to “ANALOG”
while playing a source encoded in DTS.
Set “INPUT MODE” to “AUTO” or “DTS”.
41
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
No picture
The output and input for the picture are
connected to different types of video
jacks.
Set “VIDEO CONV.” to “ON”.
94