Yamaha RX V659 MCXSP10 Manual - Page 19

Connecting the speaker cable, Connecting to the PRESENCE/ZONE2, speaker terminals, of each terminal. - zone 2

Get Yamaha RX V659 - AV Receiver PDF manuals and user guides
UPC - 027108925295
View all Yamaha RX V659 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

PREPARATION ■ Connecting the speaker cable 1 Remove approximately 10 mm (0.4 in) of insulation from the end of each speaker cable and then twist the exposed wires of the cable together to prevent short circuits. 10 mm (0.4 in) CONNECTIONS ■ Connecting to the PRESENCE/ZONE2 speaker terminals Connect presence speakers to these terminals. y You can also use these terminals to connect the Zone 2 speakers (see page 104). 1 Open the tab. 2 Loosen the knob. 2 Insert one bare wire into the hole on the side of each terminal. Red: positive (+) Black: negative (-) 3 Insert one bare wire into the hole on the side of each terminal. 3 Close the tab to secure the wire. Red: positive (+) Black: negative (-) 4 Tighten the knob to secure the wire. Red: positive (+) Black: negative (-) 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
15
CONNECTIONS
PREPARATION
■
Connecting the speaker cable
1
Remove approximately 10 mm (0.4 in) of
insulation from the end of each speaker
cable and then twist the exposed wires of the
cable together to prevent short circuits.
2
Loosen the knob.
3
Insert one bare wire into the hole on the side
of each terminal.
4
Tighten the knob to secure the wire.
■
Connecting to the PRESENCE/ZONE2
speaker terminals
Connect presence speakers to these terminals.
y
You can also use these terminals to connect the Zone 2 speakers
(see page 104).
1
Open the tab.
2
Insert one bare wire into the hole on the side
of each terminal.
3
Close the tab to secure the wire.
10 mm (0.4 in)
Red: positive (+)
Black: negative (–)
Red: positive (+)
Black: negative (–)
Red: positive (+)
Black: negative (–)