Yamaha RXV1065 Owner's Manual - Page 21

Connecting the FM and AM antennas, Connecting the power cable, Turning this unit on and off

Get Yamaha RXV1065 - RX AV Receiver PDF manuals and user guides
UPC - 027108933474
View all Yamaha RXV1065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Connections Connecting the FM and AM antennas An indoor FM antenna and an AM loop antenna are supplied with this unit. Connect these antennas properly to the respective jacks. Indoor FM antenna Outdoor AM antenna Connect a 5 to 10 m (16 to 33 ft) vinyl-covered wire, and extend it outdoors (use the AM loop antenna together with this antenna). AM loop antenna Connecting the power cable After all connections are complete, plug the power cable of this unit into an AC wall outlet. To the AC wall outlet NE2/PRESENCE CLASS 2 WIRING Power cable 2 HDMI 3 HDMI 4 ANTENNA HD Radio FM GND AM REMOTE IN UNBAL. SPEAKERS EXTRA SP ZONE2/PRESENCE SINGLE CLASS 2 WIRING Ground (GND terminal) The GND terminal is not for earth grounding. To reduce noises, connect a ground bar or a vinyl-covered wire with a copper plate at its tip, and place it in the moist ground. y • The supplied antennas are normally sensitive enough to obtain good reception. • Position the AM loop antenna away from this unit. • If you cannot get good reception, we recommend that you use an outdoor antenna. For details, consult the nearest authorized Yamaha dealer or service center. • Always use the AM loop antenna even when the outdoor antenna is connected. Assembling the AM loop antenna Connecting the AM loop antenna The wires of the AM loop antenna have no polarity. You can connect either wire to the AM terminal and the other to the GND terminal. Turning this unit on and off 1 Press KMAIN ZONE ON/OFF on the front panel (or pPOWER on the remote control) to turn on this unit. 2 Press KMAIN ZONE ON/OFF (or pPOWER) again to turn off this unit (standby mode). y • The unit needs a few seconds until ready to play back. • You can also turn on this unit by pressing PSCENE (or hSCENE). • This unit consumes a small amount of electricity even in the standby mode. We recommend disconnecting the power cable from the AC wall outlet. Caution Do not unplug this unit while it is turned on. Doing so may damage this unit or cause the settings of this unit to be saved incorrectly. Press and hold Insert Release 18 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
18
En
Connections
An indoor FM antenna and an AM loop antenna are
supplied with this unit. Connect these antennas properly to
the respective jacks.
y
•
The supplied antennas are normally sensitive enough to obtain good
reception.
•
Position the AM loop antenna away from this unit.
•
If you cannot get good reception, we recommend that you use an outdoor
antenna. For details, consult the nearest authorized Yamaha dealer or
service center.
•
Always use the AM loop antenna even when the outdoor antenna is
connected.
Assembling the AM loop antenna
Connecting the AM loop antenna
The wires of the AM loop antenna have no polarity. You
can connect either wire to the AM terminal and the other
to the GND terminal.
After all connections are complete, plug the power cable
of this unit into an AC wall outlet.
1
Press
K
MAIN ZONE ON/OFF
on the front
panel (or
p
POWER
on the remote control)
to turn on this unit.
2
Press
K
MAIN ZONE ON/OFF
(or
p
POWER
) again to turn off this unit
(standby mode).
y
•
The unit needs a few seconds until ready to play back.
•
You can also turn on this unit by pressing
P
SCENE
(or
h
SCENE
).
•
This unit consumes a small amount of electricity even in the standby
mode. We recommend disconnecting the power cable from the AC wall
outlet.
Connecting the FM and AM antennas
ANTENNA
UNBAL.
FM
HD Radio
GND
AM
2
HDMI 3
HDMI 4
IN
SPEAKERS
SINGLE
CLASS 2 WIRING
EXTRA SP
ZONE2/PRESENCE
REMOTE
Outdoor AM antenna
Connect a 5 to 10 m (16 to
33 ft) vinyl-covered wire,
and extend it outdoors
(use the AM loop antenna
together with this
antenna).
Ground (GND terminal)
The GND terminal is not for earth grounding.
To reduce noises, connect a ground bar or a
vinyl-covered wire with a copper plate at its tip,
and place it in the moist ground.
Indoor FM antenna
AM loop
antenna
Press and hold
Release
Insert
Connecting the power cable
Turning this unit on and off
Caution
Do not unplug this unit while it is turned on. Doing so
may damage this unit or cause the settings of this unit
to be saved incorrectly.
CLASS 2 WIRING
NE2/PRESENCE
To the AC wall outlet
Power cable