Yamaha RXV1065 Owner's Manual - Page 60
Sound Setup, Fr.l / Fr.r / Cntr / Sur.l / Sur.r / Sbl / Sbr
UPC - 027108933474
View all Yamaha RXV1065 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 60 highlights
INTRODUCTION PREPARATION BASIC OPERATION ADVANCED OPERATION Bass Crossover Frequency Choices: 40Hz, 60Hz, 80Hz*, 90Hz, 100Hz, 110Hz, 120Hz, 160Hz, 200Hz Sets the lower limit of the low-frequency component output from a speaker with a size set to "Small" (Small x 1, Small x 2) Sound with a frequency below that limit is output from a subwoofer or front speakers. If your subwoofer has a volume control or a crossover frequency control, set the volume to half or the crossover frequency at the maximum. Subwoofer Phase Choices: Normal*, Reverse Sets the phase of your subwoofer if bass sounds are lacking or unclear. Normal Reverse Select this not to change the phase of your subwoofer. Select this to reverse the phase of your subwoofer. ■ Speaker Level Adjustable range: -10.0dB to +10.0dB (0.5dB step) Defaults: 0dB (FR.L, FR.R, SWFR, PR.L, PR.R) -1.0dB (CNTR, SUR.L, SUR.R, SBL, SBR) Separately adjusts volume of each speaker so that the sounds form speakers are at the same volume at the listening position. Items to be displayed vary depending on the number of speakers connected. y • When only one surround back speaker is connected, "SB" appears instead of "SBL" and "SBR". • You can adjust the volume listening to test tones when you set "Test Tone" to "On" (on this page). • If your subwoofer has a volume control or a crossover frequency control, set the volume to half or the crossover frequency at the maximum. ■ Speaker Distance Adjusts timing at which each speaker outputs sound so that sounds from speakers reach the listening position at the same time. Set unit (Unit) first and set the distance of each speaker. Unit Choices: feet (ft)*, meters (m) feet (ft) meters (m) Displays the speaker distance in feet. Displays the speaker distance in meters. FR.L / FR.R / CNTR / SUR.L / SUR.R / SBL / SBR / SWFR / PR.L / PR.R Adjustable range: 0.30m to 24.00m (1.0ft to 80.0ft) Defaults: 3.00m (10.0ft) (FR.L, FR.R, SWFR, PR.L, PR.R) 2.60m (8.5ft) (CNTR) 2.40m (8.0ft) (SUR.L, SUR.R, SBL, SBR) y • Available items differ depending on the "Speaker Configuration" settings (page 55). • When only one surround back speaker is connected, "SB" appears instead of "SBL" and "SBR". Operating various settings for this unit (Setup menu) ■ Equalizer Adjusts sound quality and tone using a parametric graphic equalizer. EQ Type Select Choices: Auto PEQ, GEQ*, Off Selects an equalizer type. Auto PEQ GEQ Off Uses a parametric equalizer selected in "Auto Setup". Characteristics of the currently used parametric equalizer are displayed below "Auto PEQ". Uses a graphic equalizer. Press jENTER to adjust the characteristics of the graphic equalizer. Not use a graphic equalizer. GEQ Channels Front Left, Front Right, Center, Surround Left, Surround Right, Surround Back Left, Surround Choices: Back Right 63Hz, 160Hz, 400Hz, 1kHz, 2.5kHz, 6.3kHz, 16kHz Adjustable range: -6.0dB to 0dB* to +6.0dB (0.5dB step) Adjusts sound quality of each speaker using a graphic equalizer. The graphic equalizer of this unit can adjust signal levels in 7 frequency ranges. To adjust the signal level within each range, press jCursor l / h to select the desired speaker while "Channel" is selected, press jCursor k / n to select the desired frequency band and then press jCursor l / h to adjust the signal level. ■ Test Tone Choices: Off*, On Switches between on and off of an oscillator that generates test tones. When "On" is selected, you can adjust the settings of "Manual Setup" while listening to a test tone. Off Not generate test tones. On Generates test tones. Sound Setup You can set various items for sound outputs. ■ Dynamic Range Choices: Min/Auto, STD, Max* Selects the dynamic range adjustment method for reproducing bitstream signals. Min/Auto STD (Min) Sets the dynamic range suitable for low volume or a quiet environment, such as at night, for bitstream signals except for Dolby TrueHD signals. (Auto) Adjusts the dynamic range for Dolby TrueHD signals based on input signal information. Sets the standard dynamic range recommended for regular home use. ADDITIONAL INFORMATION APPENDIX English 57 En