Yamaha RXV1065 Owner's Manual - Page 78

Auto Setup YPAO, Before Auto Setup, During Auto Setup

Get Yamaha RXV1065 - RX AV Receiver PDF manuals and user guides
UPC - 027108933474
View all Yamaha RXV1065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

INTRODUCTION PREPARATION BASIC OPERATION ADVANCED OPERATION Troubleshooting Status message USB Connected Disconnected Access Error Unable to play Cause Remedy Your USB storage device is connected. Your USB storage device has been disconnected from the USB port of this unit. Check the connection between this unit and your USB storage device. This unit recognizes the USB storage device as an illegal device. Turn this unit off and then turn on again. This unit cannot access your USB storage Try another USB storage device. device. There is a problem with the signal path Turn off this unit and reconnect your USB storage from your USB storage device to this unit. device to the USB port of this unit. Try resetting your USB storage device. The data is invalid. Try another USB storage device. See page - - 18 - 17, 18 - - Auto Setup (YPAO) Notes • If the an error or warning message appears, resolve the problem and then run "Auto Setup" again. • Warning message "W-2" or "W-3" indicates that the adjusted settings may not be optimal. • Depending on the speakers, warning message "W-1" may appears even if the speaker connections are correct. • If error message "E-10" occurs repeatedly, contact a qualified Yamaha service center. Before Auto Setup Error message Connect MIC! Unplug HP! Memory Guard! Cause Remedy Optimizer microphone is not connected. Headphones are connected. The parameters of this unit are protected. Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel. Unplug the headphones. Set "Memory Guard" to "Off". During Auto Setup See page 19 - 60 Error message E-1:NO FRONT SP E-2:NO SUR. SP E-3:NO PRNS SP E-4:SBR->SBL E-5:NOISY E-6:CHECK SUR. Cause Remedy Front L/R channel signals are not detected. Check the front L/R speaker connections. Only a signal from one of the surround channels are detected. Check the surround L/R speaker connections. Only signals from one of the presence L/ Check the presence L/R speaker connections. R channels are detected. Only right surround back channel signal If you connect only one surround back speaker, is detected. connect it to the left SUR.BACK (SINGLE) jack. Measurement cannot be performed accurately due to loud ambient noise. Try running "Auto Setup" in a quiet environment. Turn off noisy electric equipment like air conditioners or move them away from the optimizer microphone. Surround back speakers are connected, though surround L/R speakers are not. When using surround back speakers, you need to connect surround L/R speakers. See page 11 11 11 11 - - 11 APPENDIX English 75 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
75
En
Troubleshooting
English
INTRODUCTION
APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
Notes
•
If the an error or warning message appears, resolve the problem and then run “Auto Setup” again.
•
Warning message “W-2” or “W-3” indicates that the adjusted settings may not be optimal.
•
Depending on the speakers, warning message “W-1” may appears even if the speaker connections are correct.
•
If error message “E-10” occurs repeatedly, contact a qualified Yamaha service center.
Status message
Cause
Remedy
See
page
USB Connected
Your USB storage device is connected.
—
Disconnected
Your USB storage device has been
disconnected from the USB port of this
unit.
Check the connection between this unit and your
USB storage device.
—
This unit recognizes the USB storage
device as an illegal device.
Turn this unit off and then turn on again.
18
Access Error
This unit cannot access your USB storage
device.
Try another USB storage device.
—
There is a problem with the signal path
from your USB storage device to this unit.
Turn off this unit and reconnect your USB storage
device to the USB port of this unit.
17, 18
Try resetting your USB storage device.
—
Unable to play
The data is invalid.
Try another USB storage device.
—
Auto Setup (YPAO)
Before Auto Setup
Error message
Cause
Remedy
See
page
Connect MIC!
Optimizer microphone is not connected.
Connect the supplied optimizer microphone to the
OPTIMIZER MIC jack on the front panel.
19
Unplug HP!
Headphones are connected.
Unplug the headphones.
—
Memory Guard!
The parameters of this unit are protected.
Set “Memory Guard” to “Off”.
60
During Auto Setup
Error message
Cause
Remedy
See
page
E-1:NO FRONT SP
Front L/R channel signals are not
detected.
Check the front L/R speaker connections.
11
E-2:NO SUR. SP
Only a signal from one of the surround
channels are detected.
Check the surround L/R speaker connections.
11
E-3:NO PRNS SP
Only signals from one of the presence L/
R channels are detected.
Check the presence L/R speaker connections.
11
E-4:SBR->SBL
Only right surround back channel signal
is detected.
If you connect only one surround back speaker,
connect it to the left SUR.BACK (SINGLE) jack.
11
E-5:NOISY
Measurement cannot be performed
accurately due to loud ambient noise.
Try running “Auto Setup” in a quiet environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the optimizer
microphone.
—
E-6:CHECK SUR.
Surround back speakers are connected,
though surround L/R speakers are not.
When using surround back speakers, you need to
connect surround L/R speakers.
11