Yamaha RXV1065 Owner's Manual - Page 22

Optimizing the speaker setting for your listening room (YPAO), Using Auto Setup - ypao mic

Get Yamaha RXV1065 - RX AV Receiver PDF manuals and user guides
UPC - 027108933474
View all Yamaha RXV1065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

INTRODUCTION PREPARATION BASIC OPERATION Optimizing the speaker setting for your listening room (YPAO) This unit has a Yamaha Parametric Acoustic Optimizer (YPAO). With the YPAO, this unit automatically adjusts the output characteristics of your speakers based on speaker position, speaker performance, and the acoustic characteristics of the room. We recommend that you first adjust the output characteristics with the YPAO when you use this unit. Caution • Be advised that it is normal for loud test tones to be output during the "Auto Setup" procedure. Do not allow small children to enter the room during the procedure. • To achieve the best results, make sure the room is as quiet as possible while the "Auto Setup" procedure is in progress. If there is too much ambient noise, the results may not be satisfactory. y • You can manually adjust the output characteristics of your speakers with "Manual Setup" in the Setup menu (page 55). Using Auto Setup 1 Check the following points. Before starting the automatic setup, check the following. • All speakers and subwoofer are connected properly. • Headphones are disconnected from this unit. • The video monitor is connected properly. • This unit and the video monitor are turned on. • This unit is selected as the video input source of the video monitor. • The connected subwoofer is turned on and the volume level is set to about half way (or slightly less). • The crossover frequency controls of the connected subwoofer are set to the maximum. VOLUME CROSSOVER/ HIGH CUT 2 Connect the supplied optimizer microphone to the SOPTIMIZER MIC jack on the front panel. INPUT OPTIMIZER MIC VIDEO AUX USB VIDEO AUDIO Optimizer microphone "MIC ON. View GUI MENU" appears on the front panel display. The GUI screen appears on the video monitor. Auto Setup Extra Speaker Assignment Zone2 Presence None EQ Type Flat Front Natural Start Move focus Start y • You can bring up the above menu screen from the Setup menu (page 55). 3 Place the optimizer microphone at your normal listening position on a flat level surface with the omni-directional microphone heading upward. Optimizer microphone MIN MAX MIN MAX Subwoofer y • It is recommended that you use a tripod or something similar to fix the optimizer microphone at the same height as your ears would be when seated in your listening position. You can fix the optimizer microphone to the tripod with the attaching screw of the tripod. ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 19 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
19
En
English
INTRODUCTION
ADDITIONAL
INFORMATION
APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
This unit has a Yamaha Parametric Acoustic Optimizer (YPAO). With the YPAO, this unit automatically adjusts the
output characteristics of your speakers based on speaker position, speaker performance, and the acoustic characteristics
of the room. We recommend that you first adjust the output characteristics with the YPAO when you use this unit.
1
Check the following points.
Before starting the automatic setup, check the
following.
•
All speakers and subwoofer are connected
properly.
•
Headphones are disconnected from this unit.
•
The video monitor is connected properly.
•
This unit and the video monitor are turned on.
•
This unit is selected as the video input source of the
video monitor.
•
The connected subwoofer is turned on and the
volume level is set to about half way (or slightly
less).
•
The crossover frequency controls of the connected
subwoofer are set to the maximum.
2
Connect the supplied optimizer microphone
to the
S
OPTIMIZER
MIC
jack on the front
panel.
“MIC ON. View GUI MENU” appears on the front panel
display.
The GUI screen appears on the video monitor.
y
•
You can bring up the above menu screen from the Setup menu (page 55).
3
Place the optimizer microphone at your
normal listening position on a flat level
surface with the omni-directional
microphone heading upward.
y
•
It is recommended that you use a tripod or something similar to fix the
optimizer microphone at the same height as your ears would be when
seated in your listening position. You can fix the optimizer microphone to
the tripod with the attaching screw of the tripod.
Optimizing the speaker setting for your listening room (YPAO)
Caution
•
Be advised that it is normal for loud test tones to be
output during the “Auto Setup” procedure. Do not
allow small children to enter the room during the
procedure.
•
To achieve the best results, make sure the room is as
quiet as possible while the “Auto Setup” procedure is
in progress. If there is too much ambient noise, the
results may not be satisfactory.
y
•
You can manually adjust the output characteristics of your speakers
with “Manual Setup” in the Setup menu (page 55).
Using Auto Setup
VOLUME
MIN
MAX
CROSSOVER/
HIGH CUT
MIN
MAX
Subwoofer
INPUT
VIDEO
AUDIO
VIDEO
AUX
USB
OPTIMIZER
MIC
Optimizer microphone
Auto Setup
Extra Speaker Assignment
Presence
Zone2
None
Front
Flat
Natural
EQ Type
Move focus
Start
Start
Optimizer microphone