Yamaha RXV1065 Owner's Manual - Page 71

Memory Guard! is, displayed and

Get Yamaha RXV1065 - RX AV Receiver PDF manuals and user guides
UPC - 027108933474
View all Yamaha RXV1065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Troubleshooting Problem Cause Remedy No sound is heard from the subwoofer. "LFE / Bass Out" is set to "Front" and a Dolby Digital, DTS or AAC signals is being played. Set "LFE / Bass Out" to "Subwoofer" or "Both". "LFE / Bass Out" is set to "Subwoofer" or "Front" and a 2-channel source is being played. Set "LFE / Bass Out" to "Both". The source does not contain low frequency signals. No sound is heard from the surround back speakers. "Extended Surround" in the Option menu is set to "Off", or an input signal does not contain a surround back flag with "Extended Surround" set to "Auto". Set "Extended Surround" other than "Off" or "Auto". The audio input sources cannot be played in the desired digital audio signal format. The connected component is not set to output the desired digital audio signals. Set the playback component properly referring to its operating instructions. Noise/hum noise is heard. Incorrect cable connection. Connect the audio cables properly. If the problem persists, the cables may be defective. A DTS-CD is being played back. 1) When only noise is output If a DTS bitstream signal is not properly input to this unit, only noise is output. Connect the playback component to this unit by digital connection and play back the DTS-CD. If the condition is not improved, the problem may results from the playback component. Consult the manufacturer of the playback component. 2) When noise is output during playback or skip operation Before playing back the DTS-CD, display the Option menu after selecting the input source and set "Decoder Mode" to "DTS". The volume level cannot be increased, or the sound is distorted. The component connected to the AUDIO 1/2 jacks of this unit is turned off. Turn on the power of the component. "Memory Guard!" is displayed and the setting cannot be changed. "Memory Guard" in "Set Menu" is set to Set "Memory Guard" to "Off". "On". There is noise interference from digital or radio frequency equipment. This unit is too close to other digital or radio frequency equipment. Move this unit further away from such equipment. See page 56 56 48 - - 15, 48 63 60 - 68 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
68
En
Troubleshooting
No sound is heard
from the subwoofer.
“LFE / Bass Out” is set to “Front” and a
Dolby Digital, DTS or AAC signals is
being played.
Set “LFE / Bass Out” to “Subwoofer” or “Both”.
56
“LFE / Bass Out” is set to “Subwoofer” or
“Front” and a 2-channel source is being
played.
Set “LFE / Bass Out” to “Both”.
56
The source does not contain low
frequency signals.
No sound is heard
from the surround
back speakers.
“Extended Surround” in the Option menu
is set to “Off”, or an input signal does not
contain a surround back flag with
“Extended Surround” set to “Auto”.
Set “Extended Surround” other than “Off” or “Auto”.
48
The audio input
sources cannot be
played in the desired
digital audio signal
format.
The connected component is not set to
output the desired digital audio signals.
Set the playback component properly referring to its
operating instructions.
—
Noise/hum noise is
heard.
Incorrect cable connection.
Connect the audio cables properly. If the problem
persists, the cables may be defective.
—
A DTS-CD is being played back.
1) When only noise is output
If a DTS bitstream signal is not properly input to this
unit, only noise is output. Connect the playback
component to this unit by digital connection and play
back the DTS-CD. If the condition is not improved,
the problem may results from the playback
component. Consult the manufacturer of the playback
component.
2) When noise is output during playback or skip
operation
Before playing back the DTS-CD, display the Option
menu after selecting the input source and set
“Decoder Mode” to “DTS”.
15, 48
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the AUDIO
1/2 jacks of this unit is turned off.
Turn on the power of the component.
63
“Memory Guard!” is
displayed and the
setting cannot be
changed.
“Memory Guard” in “Set Menu” is set to
“On”.
Set “Memory Guard” to “Off”.
60
There is noise
interference from
digital or radio
frequency equipment.
This unit is too close to other digital or
radio frequency equipment.
Move this unit further away from such equipment.
—
Problem
Cause
Remedy
See
page