Yamaha RXV1065 Owner's Manual - Page 76

Remote control, iPod™, Problem, Cause, Remedy, does not work or, function properly., Status message

Get Yamaha RXV1065 - RX AV Receiver PDF manuals and user guides
UPC - 027108933474
View all Yamaha RXV1065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

INTRODUCTION PREPARATION BASIC OPERATION ADVANCED OPERATION Remote control Troubleshooting Problem The remote control does not work or function properly. iPod™ Cause Remedy Wrong distance or angle. Direct sunlight or lighting (from an inverter type of fluorescent lamp, strobe light, etc.) is striking the remote control sensor of this unit. The batteries are weak. The remote control ID of the remote control and this unit do not match. The remote control code is not correctly set. Even if the remote control code is correctly set, there are some models that do not respond to the remote control. The remote control will function within a maximum range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel. Adjust the lighting angle or reposition this unit. Replace all batteries. Match the remote control ID of this unit and the remote control. Set the remote control code correctly using "List of remote control codes" at the end of this manual. Try setting another code of the same manufacturer using "List of remote control codes" at the end of this manual. If this unit does not work when you press jCursor, do the following. When the key does not work during DVD disc menu operation: press the dInput selection keys on the remote control again. When the key does not work during Option menu or Setup menu operation: press the key applicable for the current menu operation again. See page 9 - 9 64 63 63 - Note • In case of a transmission error without a status message appearing on the front panel display and GUI screen, check the connection of your iPod (page 17). Status message Cause Remedy See page Loading... This unit is in the middle of recognizing the connection with your iPod. This unit is in the middle of acquiring song lists from your iPod. Connect error There is a problem with the signal path Turn off this unit and reconnect the Yamaha iPod 17 from your iPod to this unit. universal dock to the DOCK terminal of this unit. Remove your iPod in the Yamaha iPod universal dock 42 and then place it back in the dock. Unknown iPod The iPod being used is not supported by Use an iPod supported by this unit. - this unit. iPod Connected Your iPod is properly placed in the Yamaha iPod universal dock. APPENDIX English 73 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
73
En
Troubleshooting
English
INTRODUCTION
APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
Note
•
In case of a transmission error without a status message appearing on the front panel display and GUI screen, check the connection of your iPod
(page 17).
Remote control
Problem
Cause
Remedy
See
page
The remote control
does not work or
function properly.
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees
offaxis from the front panel.
9
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, strobe
light, etc.) is striking the remote control
sensor of this unit.
Adjust the lighting angle or reposition this unit.
—
The batteries are weak.
Replace all batteries.
9
The remote control ID of the remote
control and this unit do not match.
Match the remote control ID of this unit and the
remote control.
64
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
63
Try setting another code of the same manufacturer
using “List of remote control codes” at the end of this
manual.
63
If this unit does not work when you press
j
Cursor
,
do the following.
When the key does not work during DVD disc menu
operation: press the
d
Input selection keys
on
the remote control again.
When the key does not work during Option menu or
Setup menu operation: press the key applicable for
the current menu operation again.
—
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
iPod™
Status message
Cause
Remedy
See
page
Loading...
This unit is in the middle of recognizing
the connection with your iPod.
This unit is in the middle of acquiring
song lists from your iPod.
Connect error
There is a problem with the signal path
from your iPod to this unit.
Turn off this unit and reconnect the Yamaha iPod
universal dock to the DOCK terminal of this unit.
17
Remove your iPod in the Yamaha iPod universal dock
and then place it back in the dock.
42
Unknown iPod
The iPod being used is not supported by
this unit.
Use an iPod supported by this unit.
—
iPod Connected
Your iPod is properly placed in the
Yamaha iPod universal dock.