AIWA NSX-V70 Operating Instructions - Page 14

Setting, The Clock - remote control

Get AIWA NSX-V70 PDF manuals and user guides View all AIWA NSX-V70 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

SETTING THE CLOCK When the AC cord is connected for the first time, the II SET button flashes. Set the time as follows while the power is off. 1 Press the SET button. The hour flashes. 2 Press the K DOWN or W UP button to designate the hour. 3 Press the SET button to set the hour. The hour stops flashing and the minute starts flashing. 4 Press the M DOWN or W UP button to designate the minute. 5 Press the SET button to set the minute and complete setting. The minute stops flashing on the display and the clock starts from 00 second. To correct the current time Press the POWER button to turn the unit off. Press the II SET button and carry out steps 1 to 5 above. To display the current time Press the CLOCK button on the remote control. The clock is displayed for 4 seconds. However, the time cannot be displayed during recording. To switch to the 24-hour standard Press the CLOCK button on the remote control and then press the W button within 4 seconds. Repeat the same procedure to restore the 12-hour standard. If the clock display flashes while the power is off This is caused by a power interruption. The current time needs to be reset, If power is interrupted for more than approximately 24 hours, all settings stored in memory after purchase need to be reset. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
SETTING
THE CLOCK
When
the
AC
cord
is connected
for
the
first
time,
the
II
SET
button
flashes.
Set the time as follows while the power is off.
1
2
3
4
5
Press the SET button.
The
hour flashes.
Press
the
K
DOWN
or
W
UP
button
to
designate
the hour.
Press the SET button to set the hour.
The
hour
stops
flashing
and
the minute
starts
flashing.
Press
the
M
DOWN
or
W
UP
button
to
designate
the minute.
Press
the
SET
button
to set
the
minute
and
complete
setting.
The
minute
stops
flashing
on the display
and the clock
starts
from
00 second.
To correct
the current
time
Press
the
POWER
button
to turn
the
unit off. Press
the
II
SET
button
and carry
out steps
1 to 5 above.
To display
the current
time
Press
the
CLOCK
button
on the
remote
control.
The
clock
is
displayed
for 4 seconds.
However,
the time
cannot
be displayed
during
recording.
To
switch to the 24-hour standard
Press
the CLOCK
button
on the remote
control
and then
press
the
W button
within
4 seconds.
Repeat
the same
procedure
to restore
the
12-hour
standard.
If the clock display flashes while the power is off
This
is caused
by a power
interruption.
The
current
time
needs
to be reset,
If power
is interrupted
for more
than
approximately
24 hours,
all
settings
stored
in memory
after
purchase
need
to be reset.
14