Canon MK 2600 Mk2600 Users Guide - Page 116

Printing result obtained by specifying a character alignment mode and a multiple line centering mode

Get Canon MK 2600 PDF manuals and user guides View all Canon MK 2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

4 Input characters. • Input "A-123", press [▼], and then input "R11". • Perform the printing operation. • Only 1.3mm double-byte characters can be set to three lines. • The maximum number of printable characters depends on segment length setting. If you wish to increase the number of printable characters When "Normal" is selected on the Plate Printing Area selection display, spaces are automatically inserted at the left and right of the print. When "Expansion" is selected, the printing area expands all over the segment length without inserting any space. If you wish to adjust the segment length For how to adjust the printing result finely, refer to Note, "Adjusting the segment length" ( page 101). Printing result obtained by specifying a character alignment mode and a multiple line centering mode The printing result varies depending on the choice of a character alignment mode and a multiple line centering mode. Input characters 1st line: A-123 2nd line: R11 Case 1 Cut length = 30 mm, Plate Printing Area = Normal, Character size = 2 mm/1-byte, Number of lines = 2 lines, Character alignment = Centered, Multiple line centering = On A-123 R11 Case 2 Cut length = 30 mm, Plate Printing Area = Normal, Character size = 2 mm/1-byte, Number of lines = 2 lines, Character alignment = Centered, Multiple line centering = Off A-123 R11 Case 3 Cut length = 30 mm, Plate Printing Area = Normal, Character size = 2mm/1-byte, Number of lines = 2 lines, Character alignment = Left/2 mm A-123 R11 112

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
112
4
Input characters.
• Input “A-123”, press [▼], and then input “R11”.
• Perform the printing operation.
• Only 1.3mm double-byte characters can be set to three lines.
• The maximum number of printable characters depends on segment length setting.
If you wish to increase the number of printable characters
When “Normal” is selected on the Plate Printing Area selection display, spaces are
automatically inserted at the left and right of the print. When “Expansion” is selected, the
printing area expands all over the segment length without inserting any space.
If you wish to adjust the segment length
For how to adjust the printing result finely, refer to Note, “Adjusting the segment length”
(
page 101).
Printing result obtained by specifying a character alignment mode and a multiple line centering mode
The printing result varies depending on the choice of a character alignment mode and a multiple line centering
mode.
Input characters
1st line: A-123
2nd line: R11
Case 1
Cut length = 30 mm, Plate Printing Area = Normal, Character size = 2 mm/1-byte, Number of lines = 2 lines,
Character alignment = Centered, Multiple line centering = On
A-123
R11
Case 2
Cut length = 30 mm, Plate Printing Area = Normal, Character size = 2 mm/1-byte, Number of lines = 2 lines,
Character alignment = Centered, Multiple line centering = Off
A-123
R11
Case 3
Cut length = 30 mm, Plate Printing Area = Normal, Character size = 2mm/1-byte, Number of lines = 2 lines,
Character alignment = Left/2 mm
A-123
R11