Canon MK 2600 Mk2600 Users Guide - Page 137

Replacing the Cutter

Get Canon MK 2600 PDF manuals and user guides View all Canon MK 2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

5.3 Replacing the Cutter Maintenance Part 5 If tube or label tape is not fully separated even with forced full cutting ( page 131), the cutter should be replaced. When replacing the cutter, be sure to replace the cutter receiver at the same time. Contact your nearest dealer for details on how to obtain a replacement cutter. If half cuts are too deep even though the cutting depth has been adjusted to the shallowest level, it is possible that the cutter receiver is worn. CAUTION Follow procedures! The cutter is designed so that you cannot touch it directly, but it is possible that mishandling could expose the blade, creating a risk of injury. Do not attempt any operation that is not described in this manual. Furthermore, be sure to carefully follow the procedures described in this manual. Dispose of the old cutter immediately Do not keep the old cutter after you have replaced it; dispose of it right away. The cutter poses a risk of injury to small children, etc. Discard the removed cutter immediately in compliance with local regulations regarding the disposal of such items. 1 Turn the power switch off. • Press the "O" side. 2 Open the cover. 3 Pull out the cutter. • Dispose of the old cutter right away. When disposing of the cutter, do not touch it anywhere other than where indicated in the figure. 133

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
133
Maintenance
Part 5
5.3
Replacing the Cutter
If tube or label tape is not fully separated even with forced full cutting (
page 131), the cutter should be
replaced. When replacing the cutter, be sure to replace the cutter receiver at the same time. Contact your
nearest dealer for details on how to obtain a replacement cutter.
If half cuts are too deep even though the cutting depth has been adjusted to the shallowest level, it is possible that the cutter receiver is worn.
CAUTION
Follow procedures!
The cutter is designed so that you cannot touch it directly, but it is possible that
mishandling could expose the blade, creating a risk of injury. Do not attempt any
operation that is not described in this manual. Furthermore, be sure to carefully follow
the procedures described in this manual.
Dispose of the old cutter immediately
Do not keep the old cutter after you have replaced it; dispose of it right away. The
cutter poses a risk of injury to small children, etc.
Discard the removed cutter immediately in compliance with local regulations
regarding the disposal of such items.
1
Turn the power switch off.
•
Press the “
O
” side.
2
Open the cover.
3
Pull out the cutter.
•
Dispose of the old cutter right away. When
disposing of the cutter, do not touch it anywhere
other than where indicated in the figure.