Canon XF400 XF400 XF405 Instruction Manual - Page 33

Inserting and Removing an SD Card, from the right

Get Canon XF400 PDF manuals and user guides View all Canon XF400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Using SD Cards Inserting and Removing an SD Card 1 Turn off the camcorder. ቢ • Make sure the POWER/CHG indicator is off. 33 2 Open the SD card compartment cover. • Slide the SD CARD switch all the way in the direction of the arrow to open the cover. 3 Insert the SD card straight, with the label facing away from the right side of the camcorder (the side with the air ባ intake vent), all the way into one of the SD card slots until it clicks. • You can also use two cards, one in each SD card slot. • To remove an SD card, make sure the ACCESS indicator is off and then push the card once to release it. When the SD card springs out, pull it all the way out. 4 Close the SD card compartment cover. ቤ • Do not force the cover closed if the SD card is not correctly inserted. ACCESS (SD card access) indicator SD card access indicator Red (on or flashing) Off SD card status Accessing the SD card(s). Neither SD card is being accessed or no SD cards are inserted in the camcorder. If you set [ System Setup] > [ACCESS LED] to [j Off], the ACCESS indicator will not illuminate. IMPORTANT • Observe the following precautions while the ACCESS indicator is illuminated in red. Failure to do so may result in permanent data loss. - Do not disconnect the power source or turn off the camcorder. - Do not open the SD card compartment cover. - Do not change the camcorder's operating mode. • Turn off the camcorder before inserting or removing an SD card. Inserting or removing a card with the camcorder on may result in permanent data loss. • SD cards have front and back sides that are not interchangeable. Inserting an SD card facing the wrong direction can cause a malfunction of the camcorder. Be sure to insert the SD card as described in step 3. NOTES • SD cards have a physical switch to prevent writing on the card so as to avoid the accidental erasure of the card's content. To write-protect the SD card, set the switch to the LOCK position.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
33
U
s
ing
S
D Card
s
Inserting and Removing an SD Card
1 Turn off the camcorder.
•
Make sure the POWER/CHG indicator is off.
2 Open the
S
D card compartment cover.
•
Slide the SD CARD switch all the way in the direction of the
arrow to open the cover.
3 In
s
ert the
S
D card
s
traight, with the label facing away
from the right
s
ide of the camcorder (the
s
ide with the air
inta
k
e vent), all the way into one of the
S
D card
s
lot
s
until
it clic
ks
.
•
You can also use two cards, one in each SD card slot.
•
To remove an SD card, make sure the ACCESS indicator is
off and then push the card once to release it. When the SD
card springs out, pull it all the way out.
4 Clo
s
e the
S
D card compartment cover.
•
Do not force the cover closed if the SD card is not correctly
inserted.
ACCE
SS
(
S
D card acce
ss
) indicator
If you set [
System Setup]
>
[ACCESS LED] to [
j
Off], the ACCESS indicator will not illuminate.
IMPORTANT
•
Observe the following precautions while the ACCESS indicator is illuminated in red. Failure to do so may result
in permanent data loss.
-
Do not disconnect the power source or turn off the camcorder.
-
Do not open the SD card compartment cover.
-
Do not change the camcorder’s operating mode.
•
Turn off the camcorder before inserting or removing an SD card. Inserting or removing a card with the
camcorder on may result in permanent data loss.
•
SD cards have front and back sides that are not interchangeable. Inserting an SD card facing the wrong
direction can cause a malfunction of the camcorder. Be sure to insert the SD card as described in step 3.
NOTES
•
SD cards have a physical switch to prevent writing on the card so as to avoid the accidental erasure of the
card’s content. To write-protect the SD card, set the switch to the LOCK position.
SD card access indicator
SD card status
Red (on or flashing)
Accessing the SD card(s).
Off
Neither SD card is being accessed or no SD cards are
inserted in the camcorder.
±
³
²