Cisco NAC3350-PROF-K9 Hardware Installation Guide - Page 49

Rack Installation Safety Guidelines, Four-Post (Partially-Enclosed) Rack, Four-Post (Open) Rack

Get Cisco NAC3350-PROF-K9 - NAC Profiler Server PDF manuals and user guides View all Cisco NAC3350-PROF-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Chapter 2 Preparing for Installation Preparing Your Site for Installation • Power Considerations, page 2-9 • Method of Procedure, page 2-10 Rack Installation Safety Guidelines The Cisco NAC Appliance CAM/CAS can be mounted in most four-post telephone company (telco-type), 19-inch equipment racks that comply with the Electronics Industries Association (EIA) standard for equipment racks (EIA-310-D). The distance between the center lines of the mounting holes on the two mounting posts must be 18.31 inches +/- 0.06 inch (46.50 cm +/- 0.15 cm). The rack-mounting hardware included with the appliance is suitable for most 19-inch equipment racks or telco-type frames. Note Cisco strongly recommends using four-post racks whenever possible, but your rack must have at least two posts that provide mounting flanges for mounting an appliance. Figure 2-1 shows a couple of common examples of four-post equipment racks. Figure 2-1 Four-Post Equipment Rack Types 310199 1 2 Four-Post (Partially-Enclosed) Rack Image "1" in Figure 2-1 shows a freestanding, partially-enclosed rack with two mounting posts in the front and two more at the rear. The Cisco NAC Appliance CAM/CAS may be installed in this type of enclosed rack, because the appliance only requires an unobstructed flow of cooling air into the front of the chassis and pushed out of the rear to maintain acceptable operating temperatures for its internal components. Four-Post (Open) Rack Image "2" in Figure 2-1 shows a freestanding, four-post open rack with two mounting posts in front and two mounting posts at the back. The mounting posts in this type of rack are often adjustable so that you can position the rack-mounted unit within the depth of the rack rather than flush-mount it with the front of the rack. OL-20326-01 Cisco NAC Appliance Hardware Installation Guide 2-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
2-7
Cisco NAC Appliance Hardware Installation Guide
OL-20326-01
Chapter 2
Preparing for Installation
Preparing Your Site for Installation
•
Power Considerations, page 2-9
•
Method of Procedure, page 2-10
Rack Installation Safety Guidelines
The Cisco NAC Appliance CAM/CAS can be mounted in most four-post telephone company
(telco-type), 19-inch equipment racks that comply with the Electronics Industries Association (EIA)
standard for equipment racks (EIA-310-D). The distance between the center lines of the mounting holes
on the two mounting posts must be 18.31 inches +/- 0.06 inch (46.50 cm +/- 0.15 cm). The
rack-mounting hardware included with the appliance is suitable for most 19-inch equipment racks or
telco-type frames.
Note
Cisco strongly recommends using four-post racks whenever possible, but your rack must have at least
two posts that provide mounting flanges for mounting an appliance.
Figure 2-1
shows a couple of common examples of four-post equipment racks.
Figure 2-1
Four-Post Equipment Rack Types
Four-Post (Partially-Enclosed) Rack
Image “1” in
Figure 2-1
shows a freestanding, partially-enclosed rack with two mounting posts in the
front and two more at the rear. The Cisco NAC Appliance CAM/CAS may be installed in this type of
enclosed rack, because the appliance only requires an unobstructed flow of cooling air into the front of
the chassis and pushed out of the rear to maintain acceptable operating temperatures for its internal
components.
Four-Post (Open) Rack
Image “2” in
Figure 2-1
shows a freestanding, four-post open rack with two mounting posts in front and
two mounting posts at the back. The mounting posts in this type of rack are often adjustable so that you
can position the rack-mounted unit within the depth of the rack rather than flush-mount it with the front
of the rack.
310199
1
2