Cisco NAC3350-PROF-K9 Hardware Installation Guide - Page 64

NAC-3355/3395 4-Post Rack-Mount Hardware Kit

Page 64 highlights

Rack-Mounting Your Cisco NAC Appliance CAM/CAS Chapter 2 Preparing for Installation NAC-3355/3395 4-Post Rack-Mount Hardware Kit Figure 2-9 shows the items that you need to install the NAC-3355/3395 appliance in a 4-post rack. Figure 2-9 NAC-3355/3395 Rack Installation Kit Contents Cable-management Cable-management arm stop bracket arm mounting bracket (Not used) Slide rail (left) Slide rail (right) Cable-management support arm EIA latches (2) Front of rails Cable-management arm assembly Large cable tie (1) Cable ties (5) Cage nuts (13) 10-32 screws 12-24 screws M6 screws (13) (13) (13) Clip nuts (13) 253136 Note Some of the items in Figure 2-9 are shipped in the NAC-3355/3395 shipping container, not necessarily with the rack installation kit. Installing the NAC-3355/3395 Slide Rails Into the 4-Post Rack When installing the NAC-3355/3395 slide rails in your equipment rack, Cisco recommends using cage nuts with square-holed racks, clip nuts with round-holed racks, and your own rack screws with thread-hole racks. Note If the slide rails that arrived in your shipping container include shipping thumbscrews, remove them before performing the following procedure. Step 1 Step 2 Step 3 Identify an available space in your rack to install the NAC-3355/3395. If you have either a round-holed or square-holed rack, install cage nuts or clip nuts, in the middle and bottom holes of the rack unit space on each side of the rack your NAC-3355/3395 will occupy (see Figure 2-10). Install cage nuts or clip nuts in the top and bottom holes for each side of the respective rear rack mounting rails (see Figure 2-10). 2-22 Cisco NAC Appliance Hardware Installation Guide OL-20326-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176

2-22
Cisco NAC Appliance Hardware Installation Guide
OL-20326-01
Chapter 2
Preparing for Installation
Rack-Mounting Your Cisco NAC Appliance CAM/CAS
NAC-3355/3395 4-Post Rack-Mount Hardware Kit
Figure 2-9
shows the items that you need to install the NAC-3355/3395 appliance in a 4-post rack.
Figure 2-9
NAC-3355/3395 Rack Installation Kit Contents
Note
Some of the items in
Figure 2-9
are shipped in the NAC-3355/3395 shipping container, not necessarily
with the rack installation kit.
Installing the NAC-3355/3395 Slide Rails Into the 4-Post Rack
When installing the NAC-3355/3395 slide rails in your equipment rack, Cisco recommends using cage
nuts with square-holed racks, clip nuts with round-holed racks, and your own rack screws with
thread-hole racks.
Note
If the slide rails that arrived in your shipping container include shipping thumbscrews, remove them
before performing the following procedure.
Step 1
Identify an available space in your rack to install the NAC-3355/3395.
Step 2
If you have either a round-holed or square-holed rack, install cage nuts or clip nuts, in the middle and
bottom holes of the rack unit space on each side of the rack your NAC-3355/3395 will occupy (see
Figure 2-10
).
Step 3
Install cage nuts or clip nuts in the top and bottom holes for each side of the respective rear rack
mounting rails (see
Figure 2-10
).
Large
cable tie
(1)
M6 screws
(13)
Cage nuts
(13)
Cable ties
(5)
Slide rail
(right)
Slide rail
(left)
Cable-management
arm assembly
Front of rails
10-32 screws
(13)
Cable-management
support arm
Cable-management
arm stop bracket
12-24 screws
(13)
EIA latches
(2)
Clip nuts
(13)
Cable-management
arm mounting bracket
(Not used)
253136