Compaq 100B Maintenance and Service Guide - Page 43

Power Switch/LED Assembly,

Get Compaq 100B PDF manuals and user guides View all Compaq 100B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Power Switch/LED Assembly 1. Prepare the computer for disassembly (Preparation for Disassembly on page 22). 2. Remove the access panel (Access Panel on page 23). 3. Lay the computer on its side with the front facing toward you. 4. Remove the front bezel (Front Bezel on page 24). 5. Remove the optical drive (Removing an Optical Drive on page 31). 6. Remove the hard drive (Removing the Hard Drive on page 32). 7. Disconnect the cable from the black system board connector. 8. Remove the cable from the clips under the hard drive cage. Figure 5-13 Removing the power switch cable 9. Press the tab (1) on the bottom of the power switch to disengage it from the chassis, slide the switch downward to disengage the tabs from the chassis (2), and then pull the power switch away from the chassis while guiding the wires through the hole in the chassis. Figure 5-14 Removing the power switch 10. Remove the power switch cable from the clips located in the optical drive bay on the inside of the chassis. To install the power switch/LED assembly, reverse the removal procedures. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
35
Power Switch/LED Assembly
1.
Prepare the computer for disassembly (
Preparation for Disassembly on page 22
).
2.
Remove the access panel (
Access Panel on page 23
).
3.
Lay the computer on its side with the front facing toward you.
4.
Remove the front bezel (
Front Bezel on page 24
).
5.
Remove the optical drive (
Removing an Optical Drive on page 31
).
6.
Remove the hard drive (
Removing the Hard Drive on page 32
).
7.
Disconnect the cable from the black system board connector.
8.
Remove the cable from the clips under the hard drive cage.
Figure 5-13
Removing the power switch cable
9.
Press the tab
(1)
on the bottom of the power switch to disengage it from the chassis, slide the
switch downward to disengage the tabs from the chassis
(2)
, and then pull the power switch
away from the chassis while guiding the wires through the hole in the chassis.
Figure 5-14
Removing the power switch
10.
Remove the power switch cable from the clips located in the optical drive bay on the inside of the
chassis.
To install the power switch/LED assembly, reverse the removal procedures.