D-Link DMS-1100 User Manual - Page 40

System > System Log > System Log Settings, Source Interface State

Get D-Link DMS-1100 PDF manuals and user guides View all D-Link DMS-1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

D-Link DMS-1100 Series User Manual Retry Count Waiting Time Action Specify the retry count when failed to detect the PD host. Default value is 2 times. The count range is 0 ~ 5 times (0 referring to retry mechanism turned off). The time interval that PD alive feature waiting between retry executed. The default value is 180 seconds. The interval range is 30 ~ 300 seconds. The action that executed when PD host is determined failed in detection. "Reset" means the port reset when failure occurred. "Notify" means system sending syslog for the specific failure event. "Both" referring to execute both actions above when failure occurred. The default action is "Both". Table 4.18 System > System Log > System Log Settings The System Log Settings page allows user to view and configure the system's log settings. Figure 4.37 - System > System Log > System Log Settings The fields that can be configured for System Log Settings are described below: Item Description Global Settings Source Interface State Select to enable or disable the source interface's global state. Type Select the type of interface that will be used. The default option is VLAN. VID (1-4094) Specifies the VLAN ID. The possible range is 1 - 4094. Buffer Log Settings Buffer Log State Select to enable or disable the buffer log state. Severity Write Delay (0-65535) Select the severity value of the type of information that will be logged. The values are 0 (Emergencies), 1 (Alerts), 2 (Critical), 3 (Errors), 4 (Warnings), 5 (Notifications), 6 (Informational), and 7 (Debugging). Enter the interval for periodic writing of the logging buffer to flash. The value is between 0 and 65535 seconds. And default is 300 seconds. Tick the Infinite option, to disable the write delay feature. Table 4.19 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
D-Link DMS-1100 Series User Manual
34
Retry Count
Specify the retry count when failed to detect the PD host. Default value
is 2 times. The count range is 0 ~ 5 times (0 referring to retry
mechanism turned off).
Waiting Time
The time interval that PD alive feature waiting between retry executed.
The default value is 180 seconds. The interval range is 30 ~ 300
seconds.
Action
The action that executed when PD host is determined failed in
detection.
“
Reset
” means the port reset when failure occurred.
“
Notify
” means system sending syslog for the specific failure event.
“
Both
” referring to execute both actions above when failure occurred.
The default action is “
Both
”.
Table 4.18
System > System Log > System Log Settings
The System Log Settings page allows user to view and configure the system’s log settings.
Figure 4.37 – System > System Log > System Log Settings
The fields that can be configured for
System Log Settings
are described below:
Item
Description
Global Settings
Source Interface State
Select to enable or disable the source interface’s global state.
Type
Select the type of interface that will be used. The default option is
VLAN
.
VID (1-4094)
Specifies the VLAN ID. The possible range is
1 – 4094
.
Buffer Log Settings
Buffer Log State
Select to enable or disable the buffer log state.
Severity
Select the severity value of the type of information that will be logged.
The values are 0 (Emergencies),
1 (Alerts)
,
2 (Critical)
,
3 (Errors)
,
4
(Warnings)
,
5 (Notifications)
,
6 (Informational)
, and
7 (Debugging)
.
Write Delay (0-65535)
Enter the interval for periodic writing of the logging buffer to flash.
The
value is between 0 and 65535 seconds. And default is 300 seconds.
Tick the Infinite option, to disable the write delay feature.
Table 4.19