Dell PowerEdge MX7000 EMC OpenManage Enterprise-Modular Edition Version 1.20.1 - Page 32

Con chassis location, Table 7. Chassis Direct-LED blink status and description

Get Dell PowerEdge MX7000 PDF manuals and user guides View all Dell PowerEdge MX7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Remove the USB cable that is connected to the front panel and AC power cycle the chassis. With the system that is connected to the USB OTG port on the chassis, you can access the MM user interface and iDRAC user interface or KVM. You can get access by launching a browser on the laptop and entering the URL, https://ome-m.local. A chassis phonebook page which contains a list of entries to the available devices on the chassis, is displayed. This option provides a better experience than the front panel KVM, which provides access only the command-line prompt access for OME-Modular. Select the check box to enable accessing the MX7000 chassis from a host such as a laptop or server, using a USB On-The-Go (OTG) cable. Connect the USB OTG cable from the host to the micro USB port on the front panel (right control panel) of the MX7000 chassis. On successful connection, LED under the micro-USB on the right control panel of MX7000 chassis turns green and USB Ethernet adapter is displayed on the host. The chassis is automatically configured with an IPV4 and IPV6 address. After ensuring that the addresses are configured, open a web browser and enter the URL, https://ome-m.local in the address bar. On laptops running Windows, if the IPV6 traffic is blocked, check the Remote Network Driver Interface Specification (RNDIS) interface for IPv6 address. You may be able to access chassis phonebook page through IPv4, but iDRAC and OME-Modular web consoles are inaccessible. In that case, enable IPv6 traffic flow on the system. When you enable or disable the Chassis Direct feature in OME-Modular, the following error codes are displayed: The Chassis Direct feature in OME-Modular has a mutual exclusivity with the Quick Sync feature. Before downgrading the management module firmware from 1.10.00 version to an earlier version, remove the USB cable that is connected to the front panel of chassis. If USB cable is not removed and 1.10.00 firmware is downgraded, the Quick Sync feature may be degraded. AC power cycle of chassis to restore Quick Sync back to health. ● The chassis has Quick Sync, and the Chassis Direct feature is enabled. That is, the USB cable is attached to the USB connector on the front panel. ● The management module version is downgraded from 1.10.00 to an earlier version. Table 7. Chassis Direct-LED blink status and description Error code Chassis Direct LED blink status 1 Amber Description and resolution The USB network link is down as the Chassis Direct feature is disabled. Resolution-Enable the Chassis Direct and reattach the USB cable to access the chassis phonebook. 2 Amber The USB network link does not come up as the chassis internal USB operation failed. Resolution-If the issue persists, reattach the USB cable to the laptop or perform and AC power cycle of the chassis. 3 Amber The USB network link fails to come up owing to an issue on the host laptop. Resolution-If the issue persists, reattach the USB cable. 4 Turned off The USB network link is down as the USB cable is disconnected. Resolution-Reattach the USB cable for the link to come up. If the Chassis Direct feature is disabled and the USB cable is inserted, the Chassis Direct LED turns amber and the alert, USR0197, is displayed on the OME-Modular web interface. You can see the alert only if you have logged in to OME-Modular using the public network. If you repeat the action within a short interval, the alert is not displayed. However, the Chassis Direct LED remains amber as the MM suppresses consecutive duplicate alerts. Configure chassis location To configure the location of the chassis: 32 Logging in to OME-Modular

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
Remove the USB cable that is connected to the front panel and AC power cycle the chassis.
With the system that is connected to the USB OTG port on the chassis, you can access the MM user interface and iDRAC user
interface or KVM. You can get access by launching a browser on the laptop and entering the URL,
https://ome-m.local
. A
chassis phonebook page which contains a list of entries to the available devices on the chassis, is displayed. This option provides
a better experience than the front panel KVM, which provides access only the command-line prompt access for OME-Modular.
Select the check box to enable accessing the MX7000 chassis from a host such as a laptop or server, using a USB On-The-Go
(OTG) cable. Connect the USB OTG cable from the host to the micro USB port on the front panel (right control panel) of the
MX7000 chassis. On successful connection, LED under the micro-USB on the right control panel of MX7000 chassis turns green
and USB Ethernet adapter is displayed on the host. The chassis is automatically configured with an IPV4 and IPV6 address. After
ensuring that the addresses are configured, open a web browser and enter the URL,
https://ome-m.local
in the address
bar.
On laptops running Windows, if the IPV6 traffic is blocked, check the Remote Network Driver Interface Specification (RNDIS)
interface for IPv6 address. You may be able to access chassis phonebook page through IPv4, but iDRAC and OME-Modular web
consoles are inaccessible. In that case, enable IPv6 traffic flow on the system.
When you enable or disable the Chassis Direct feature in OME-Modular, the following error codes are displayed:
The Chassis Direct feature in OME-Modular has a mutual exclusivity with the Quick Sync feature. Before downgrading the
management module firmware from 1.10.00 version to an earlier version, remove the USB cable that is connected to the front
panel of chassis. If USB cable is not removed and 1.10.00 firmware is downgraded, the Quick Sync feature may be degraded. AC
power cycle of chassis to restore Quick Sync back to health.
●
The chassis has Quick Sync, and the Chassis Direct feature is enabled. That is, the USB cable is attached to the USB
connector on the front panel.
●
The management module version is downgraded from 1.10.00 to an earlier version.
Table 7. Chassis Direct—LED blink status and description
Error code
Chassis Direct LED blink status
Description and resolution
1
Amber
The USB network link is down as the
Chassis Direct feature is disabled.
Resolution
—Enable the Chassis Direct
and reattach the USB cable to access
the chassis phonebook.
2
Amber
The USB network link does not come up
as the chassis internal USB operation
failed.
Resolution
—If the issue persists,
reattach the USB cable to the laptop or
perform and AC power cycle of the
chassis.
3
Amber
The USB network link fails to come up
owing to an issue on the host laptop.
Resolution
—If the issue persists,
reattach the USB cable.
4
Turned off
The USB network link is down as the
USB cable is disconnected.
Resolution
—Reattach the USB cable
for the link to come up.
If the Chassis Direct feature is disabled and the USB cable is inserted, the Chassis Direct LED turns amber and the alert,
USR0197, is displayed on the OME-Modular web interface. You can see the alert only if you have logged in to OME-Modular
using the public network. If you repeat the action within a short interval, the alert is not displayed. However, the Chassis Direct
LED remains amber as the MM suppresses consecutive duplicate alerts.
Configure chassis location
To configure the location of the chassis:
32
Logging in to OME-Modular