Dell PowerEdge MX7000 EMC OpenManage Enterprise-Modular Edition Version 1.20.1 - Page 77

Configuring IOM management settings, Alternate DNS Server 2

Get Dell PowerEdge MX7000 PDF manuals and user guides View all Dell PowerEdge MX7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

To configure the networking settings: 1. Click All Devices > I/O Modules > View Details > Settings > Network or Devices > I/O Modules > View Details > Settings > Network. 2. In the IPv4 Settings section, select Enable IPv4. 3. Enter the IP Address, Subnet Mask, and Gateway for the management port. The IP Address, Subnet Mask, and Gateway options are enabled only if the Enable DHCP check box is cleared. NOTE: For MX5108n and MX9116n IOMs, the default prefix length of the DHCP IP is 128 bits, though the DHCP server is configured for 64 bits. 4. In the IPv6 Settings section, select Enable IPv6. 5. Enter the IPv6 Address, select the Prefix Length. The IPv6 Address, Prefix Length, and Gateway options are enabled only if the Enable Autoconfiguration check box is cleared. 6. Enter the Gateway for the management port. The IPv6 Address, Prefix Length, and Gateway options are enabled only if the Enable Autoconfiguration check box is cleared. NOTE: For tagged or untagged VLAN network, any IPv6 setting configured using OME - Modular may not have the default gateway. To get the default gateway, go to the respective OS10 CLI and disable the Stateless Address Autoconfiguration (SLAAC) on the respective tagged or untagged VLAN. 7. In the DNS Server Settings section, enter the Preferred DNS Server, Alternate DNS Server 1, and Alternate DNS Server 2 addresses. For MXG610s IOMs, you can set the Preferred DNS and Alternate Server 1 and 2 addresses. However, the server address for Alternate DNS Server 2 is not applied though the response is successful as, MXG610s IOMs support only two server address for DNS settings. 8. In the Management VLAN section, select Enable VLAN and enter the VLAN ID. For MXG610s FC IOMs, DHCP works only without VLAN while Static IP works with or without VLAN configuration. To change the IP configuration from DHCP IP to Static IP, perform the following steps: a. Disable DHCP, configure the static IP, and save the configuration. b. Enable VLAN, configure the VLAN ID, and save the configuration. Configuring IOM management settings The management settings for IOMs include configuring the hostname and password of the management system. 1. Click All Devices > I/O Modules > View Details > Settings > Management or Devices > I/O Modules > View Details > Settings > Management. 2. In the Host Name section, enter the name of the management system. If you modify the hostname settings in the OME-Modular web interface for Fibre Channel IOM, the modified hostname for Fibre Channel IOMs is displayed only in a new session. To see the modified hostname, log out and log in back to the session. 3. Enter the password to access the management system. NOTE: For Ethernet IOMs with OS10 version 10.5.0.7 and later and MXG610s, it sets the admin account password. For OS10 versions earlier than 10.5.0.7, it sets the linuxadmin account password. NOTE: The OS10 password length must be with minimum 9 characters. It is recommended to have at least one upper case, one lower case, one numeric character and one special character for stronger password. By default, the minimum number of different character settings are set as 0. You can use password-attributes command to configure wanted password strength. 4. Click Apply to save the management settings or click Discard to clear the changes and go back to the previous settings. Configuring IOM monitoring settings The monitoring settings for IOMs include configuring the settings to monitor SNMP.. Ethernet IO Modules 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
To configure the networking settings:
1.
Click
All Devices
>
I/O Modules
>
View Details
>
Settings
>
Network
or
Devices
>
I/O Modules
>
View Details
>
Settings
>
Network
.
2.
In the
IPv4 Settings
section, select
Enable IPv4
.
3.
Enter the
IP Address
,
Subnet Mask
, and
Gateway
for the management port.
The
IP Address
,
Subnet Mask
, and
Gateway
options are enabled only if the
Enable DHCP
check box is cleared.
NOTE:
For MX5108n and MX9116n IOMs, the default prefix length of the DHCP IP is 128 bits, though the DHCP server
is configured for 64 bits.
4.
In the
IPv6 Settings
section, select
Enable IPv6
.
5.
Enter the
IPv6 Address
, select the
Prefix Length
.
The
IPv6 Address
,
Prefix Length
, and
Gateway
options are enabled only if the
Enable Autoconfiguration
check box is
cleared.
6.
Enter the
Gateway
for the management port.
The
IPv6 Address
,
Prefix Length
, and
Gateway
options are enabled only if the
Enable Autoconfiguration
check box is
cleared.
NOTE:
For tagged or untagged VLAN network, any IPv6 setting configured using OME - Modular may not have the
default gateway. To get the default gateway, go to the respective OS10 CLI and disable the Stateless Address
Autoconfiguration (SLAAC) on the respective tagged or untagged VLAN.
7.
In the
DNS Server Settings
section, enter the
Preferred DNS Server
,
Alternate DNS Server 1
, and
Alternate DNS
Server 2
addresses.
For MXG610s IOMs, you can set the Preferred DNS and Alternate Server 1 and 2 addresses. However, the server address for
Alternate DNS Server 2
is not applied though the response is successful as, MXG610s IOMs support only two server
address for DNS settings.
8.
In the
Management VLAN
section, select
Enable VLAN
and enter the
VLAN ID
.
For MXG610s FC IOMs, DHCP works only without VLAN while Static IP works with or without VLAN configuration. To
change the IP configuration from DHCP IP to Static IP, perform the following steps:
a.
Disable DHCP, configure the static IP, and save the configuration.
b.
Enable VLAN, configure the VLAN ID, and save the configuration.
Configuring IOM management settings
The management settings for IOMs include configuring the hostname and password of the management system.
1.
Click
All Devices
>
I/O Modules
>
View Details
>
Settings
>
Management
or
Devices
>
I/O Modules
>
View Details
>
Settings
>
Management
.
2.
In the
Host Name
section, enter the name of the management system.
If you modify the hostname settings in the OME-Modular web interface for Fibre Channel IOM, the modified hostname for
Fibre Channel IOMs is displayed only in a new session. To see the modified hostname, log out and log in back to the session.
3.
Enter the password to access the management system.
NOTE:
For Ethernet IOMs with OS10 version 10.5.0.7 and later and MXG610s, it sets the admin account password. For
OS10 versions earlier than 10.5.0.7, it sets the linuxadmin account password.
NOTE:
The OS10 password length must be with minimum 9 characters. It is recommended to have at least one upper
case, one lower case, one numeric character and one special character for stronger password. By default, the minimum
number of different character settings are set as 0. You can use
password-attributes
command to configure wanted
password strength.
4.
Click
Apply
to save the management settings or click
Discard
to clear the changes and go back to the previous settings.
Configuring IOM monitoring settings
The monitoring settings for IOMs include configuring the settings to monitor SNMP..
Ethernet IO Modules
77