Dell PowerEdge T350 EMC Installation and Service Manual - Page 31

Installing the system feet, Removing the system feet

Get Dell PowerEdge T350 PDF manuals and user guides View all Dell PowerEdge T350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Figure 14. Removing the system feet Next steps 1. Replace the system feet. Installing the system feet Prerequisites CAUTION: Install the feet on a stand-alone tower system to provide stability to the system. An unstable system might tip over and cause injury to the user or damage to the system. 1. Follow the safety guidelines listed in Safety instructions. 2. Place the system on its side on a flat, stable surface. Steps 1. Align the three tabs on the system foot with the three slots on the base of the system. 2. Using the Phillips 2 screwdriver, secure the feet to the base of the system with a screw. 3. Repeat the above steps to install the remaining system feet. Installing and removing system components 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Figure 14. Removing the system feet
Next steps
1.
Replace the system feet
.
Installing the system feet
Prerequisites
CAUTION:
Install the feet on a stand-alone tower system to provide stability to the system. An unstable system
might tip over and cause injury to the user or damage to the system.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Place the system on its side on a flat, stable surface.
Steps
1.
Align the three tabs on the system foot with the three slots on the base of the system.
2.
Using the Phillips 2 screwdriver, secure the feet to the base of the system with a screw.
3.
Repeat the above steps to install the remaining system feet.
Installing and removing system components
31