Dell PowerEdge T350 EMC Installation and Service Manual - Page 81

Optional IDSDM module, Removing the IDSDM module

Get Dell PowerEdge T350 PDF manuals and user guides View all Dell PowerEdge T350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Figure 70. Installing the BOSS S2 card carrier Next steps 1. Connect the BOSS S2 power and signal cables to the connectors on the BOSS S2 module and system board. NOTE: Insert the BOSS S2 power and signal cable through the cable clip. 2. Follow the procedure listed in the After working inside your system. 3. Install the front bezel. Optional IDSDM module Removing the IDSDM module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud. 4. If you are replacing the IDSDM card, remove the MicroSD cards. NOTE: Temporarily label each SD card with its corresponding slot number before removal. Reinstall the SD cards into the corresponding slots. Steps Holding the pull tab, lift the IDSDM card out of the system. Installing and removing system components 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Figure 70. Installing the BOSS S2 card carrier
Next steps
1.
Connect the BOSS S2 power and signal cables to the connectors on the BOSS S2 module and system board.
NOTE:
Insert the BOSS S2 power and signal cable through the cable clip.
2.
Follow the procedure listed in the
After working inside your system
.
3.
Install the front bezel
.
Optional IDSDM module
Removing the IDSDM module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud
.
4.
If you are replacing the IDSDM card, remove the MicroSD cards.
NOTE:
Temporarily label each SD card with its corresponding slot number before removal. Reinstall the SD cards into
the corresponding slots.
Steps
Holding the pull tab, lift the IDSDM card out of the system.
Installing and removing system components
81