Dell S3100 Command Line Reference Guide for the Series 9.100.1 - Page 783

Version 7.6.1.0 Description Introduced on the S-Series. Usage Information The following describes the show ip fib stack-unit command shown in the following example. Field Destination Description Lists the destination IP address. Gateway First-Hop Mac-Addr Port VId EC Displays either the word "direct" and an interface for a directly connected route or the remote IP address used to forward the traffic. Displays the first hop IP address. Displays the MAC address. Displays the egress-port information. Displays the VLAN ID. If no VLAN is assigned, zero (0) is listed. Displays the number of ECMP paths. If weighted ECMP is enabled, then the show ip fib stack-unit command display a new column named W-EC (Weighted ECMP). This column displays either a value of 1 or 0 depending on whether or not a route is assigned with a weight. Example Example (Show command output with Weighted ECMP Enabled) Dell# show ip fib stack-unit 1 Destination Gateway First-Hop Mac-Addr Port VId EC 1.1.1.2/32 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Gi 3/42 1000 0 2.1.1.2/32 via 2.1.1.2, Vl 20 2.1.1.2 00:03:00:00:00:02 Po 10 20 0 0.0.0.0/0 - 0.0.0.0 00:00:00:00:00:00 CP 0 0 1.1.1.0/24 Direct, Vl 1000 0.0.0.0 00:00:00:00:00:00 CP 1000 0 1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 2.1.1.0/24 Direct, Vl 20 0.0.0.0 00:00:00:00:00:00 CP 20 0 2.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 100.1.1.0/24 via 1.1.1.2, Vl 1000 1.1.1.2 00:01:00:00:00:02 Gi 3/42 1000 1 100.1.1.0/24 via 2.1.1.2, Vl 20 2.1.1.2 00:03:00:00:00:02 Po 10 20 1 Dell# Dell# show ip route S 10.1.1.0/24 S 20.1.1.0/24 S 100.1.1.0/24 via 1.1.1.2, Vl 10 via 2.1.1.2, Vl 20 via 3.1.1.2, Vl 30 via 10.1.1.0, weight 7 via 20.1.1.0, weight 1 Dell# show ip fib stack-unit 1 Destination Gateway First-Hop Mac-Addr Port VId EC RC W 0.0.0.0/0 - 0.0.0.0 00:00:00:00:00:00 CP 0 0 - - 1.1.0/24 Direct, Lo 0 0.0.0.0 00:00:00:00:00:00 CP 0 0 - - 1.1.1.1/32 via 127.0.0.1 127.0.0.1 00:00:00:00:00:00 CP 0 0 - - The RC and W columns in the show output appear only if the weighted ECMP is enabled using the ip ecmp weighted command. Related Commands • clear ip fib stack-unit - clear FIB entries on a specified stack-unit. • ip ecmp weighted- enable weighted ECMP calculations. show ip flow Show how a Layer 3 packet is forwarded when it arrives at a particular interface. Syntax show ip flow interface interface {source-ip address destination-ip address} {protocol number [tcp | udp]} {src-port number destination-port number} IPv4 Routing 783