Denon AVR 3806 Owners Manual - Page 15

Setup Mic, On/standby, Power - controller

Get Denon AVR 3806 - AV Receiver PDF manuals and user guides
UPC - 081757506786
View all Denon AVR 3806 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Easy Setup and Operation POWER ENTER SETUP MIC SYSTEM SETUP ON/STANDBY CURSOR AMP SYSTEM SETUP CURSOR ON OFF ENTER Connecting a microphone Easy Setup and Operation Turning on the power 1 Connect the microphone for Auto Setup to the SETUP MIC jack on the front panel of the unit. 1 Turn on your subwoofer. Set the volume to halfway and set the crossover frequency to the maximum or Low pass filter off if your subwoofer can adjust the output volume and the crossover frequency Some subwoofers have a standby mode. Be sure to turn this function off before performing the Auto Setup procedure. 2 Mount the auto setup microphone onto a camera tripod, etc., and place it at ear height at the main listening position in the listening room with the sound receptor facing the ceiling. Microphone 2 Turn on your monitor (TV). 3 Press the POWER switch. ¢ ON: The power turns on and the indicator lights. Set the POWER switch to this position to turn the power on and off from the included remote control unit. £ OFF: The power turns off and the indicator is off. In this position, the power cannot be turned on and off from the remote control unit. When placing the microphone, adjust the height so that the microphone's sound receptor is at the height of the ears of the listener. Be sure that at the beginning, the measurement is started with the microphone set up at the main listening position. It is not possible to measure properly if there are any obstacles between the speakers and microphone. Check that there are no obstacles. Please do not stand between or near the speakers and the microphone during the measurements. 4 Press the ON/STANDBY switch on the main unit or ON button on the remote control unit. • When pressed, the power turns on and the display lights. • When pressed again, the power turns off, the standby mode is set and the display turns off. The sound is muted for several seconds, after which the unit operates normally. When ever the ON/STANDBY button is in the standby state, the apparatus is still connected to the AC line voltage. Please be sure to turn off the POWER switch or unplug the cord when you leave home for, say, a vacation. NOTE: • Do not disconnect the microphone until the settings are completed. • Do not change the connection of speakers or the subwoofer's volume after performing these measurements. 5 Press the AMP button to select the "AMP" mode (only when operating with the remote control unit ( page 26)). 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
10
Easy Setup and Operation
Easy Setup and Operation
Connecting a microphone
1
Connect the microphone for Auto Setup to the
SETUP MIC
jack on the front panel of the unit.
2
Mount the auto setup microphone onto a camera
tripod, etc., and place it at ear height at the main
listening position in the listening room with the
sound receptor facing the ceiling.
Microphone
NOTE:
• Do not disconnect the microphone until the settings are
completed.
• Do not change the connection of speakers or the
subwoofer’s volume after performing these measurements.
When placing the microphone, adjust the height so that the
microphone’s sound receptor is at the height of the ears of
the listener.
Be sure that at the beginning, the measurement is started
with the microphone set up at the main listening position.
It is not possible to measure properly if there are any
obstacles between the speakers and microphone. Check
that there are no obstacles.
Please do not stand between or near the speakers and the
microphone during the measurements.
ENTER
ON
OFF
CURSOR
SYSTEM
SETUP
AMP
ON/STANDBY
SYSTEM
SETUP
CURSOR
POWER
ENTER
SETUP MIC
4
Press the
ON/STANDBY
switch on the main unit
or
ON
button on the remote control unit.
• When pressed, the power turns on and the display lights.
• When pressed again, the power turns off, the standby
mode is set and the display turns off.
3
Press the
POWER
switch.
£
OFF:
The power turns off and the indicator is off.
In this position, the power cannot be turned on and off from
the remote control unit.
¢
ON:
The power turns on and the indicator lights.
Set the
POWER
switch to this position to turn the power on
and off from the included remote control unit.
1
Turn on your subwoofer.
Turn on your monitor (TV).
Turning on the power
5
Press the
AMP
button to select the “AMP” mode
(only when operating with the remote control
unit
(
page 26)
).
2
The sound is muted for several seconds, after which the
unit operates normally.
When ever the
ON/STANDBY
button is in the standby state,
the apparatus is still connected to the AC line voltage.
Please be sure to turn off the
POWER
switch or unplug the
cord when you leave home for, say, a vacation.
Set the volume to halfway and set the crossover frequency
to the maximum or Low pass filter off if your subwoofer can
adjust the output volume and the crossover frequency
Some subwoofers have a standby mode. Be sure to turn
this function off before performing the Auto Setup
procedure.