Epson 890N Service Manual - Page 33

Buzzer, Default Setting

Get Epson 890N - FX B/W Dot-matrix Printer PDF manuals and user guides
UPC - 010343850019
View all Epson 890N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

EPSON FX-890/2190 1.3.4 Buzzer This printer has the buzzer to indicate its current condition with the following indications. The symbols used in the table above represent the following: "•" Short Beep (Beeper sounds about 100 ms and interval is about100 ms) "-" Long Beep (Beeper sounds about 500 ms and interval is about100 ms) Table 1-37. Buzzer Status Printer status Paper out error Beep sounds ••• Release lever operation error ••• Cover open error ••• Paper eject error ••• Panel operation • Fatal error *1 ----- Note "*1": The printer detects various type of "Fatal Error" condition and a type of error is memorized in EEPROM of the main controller board. Refer to Chapter-3: 3.2.12 Fatal Error for details. Revision B 1.3.5 Default Setting You can change some parameters that the printer refers to at printer initialization. 1.3.5.1 Setting Method Refer to the following flowchart for default setting. START Holding down Item ↓ (Font) button, turn the printer on. Language selection sheet. Change the language? NO YES Press Item ↓ (Font) button to select the aimed language. Press Set (Tear Off/Bin) button. The current setting value and the language that was selected will be printed. Finish? YES NO Press Set (Tear Off/Bin) button. The select sheet will be printed. Referring to Font LEDs, press Item ↓ (Font) or Item ↑ (Pitch) button to select the menu. Referring to Pitch LEDs, press Set (Tear Off/Bin) button to change the setting value. NO Finish? YES Press Menu (Pitch & Tear Off/Bin) button. * * The printer will exit from the default setting mode after storing the setting into non-volatile memory. END Figure 1-14. Flowchart for Default Setting PRODUCT DESCRIPTIONS Operation 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
EPSON FX-890/2190
Revision B
PRODUCT DESCRIPTIONS
Operation
33
1.3.4
Buzzer
This printer has the buzzer to indicate its current condition with the following
indications.
The symbols used in the table above represent the following:
“
•
”
Short Beep (Beeper sounds about 100 ms and interval is about100 ms)
“-”
Long Beep (Beeper sounds about 500 ms and interval is about100 ms)
Note
“*1”:
The printer detects various type of “Fatal Error” condition and a type of error is
memorized in EEPROM of the main controller board. Refer to
Chapter-3: 3.2.12
Fatal Error
for details.
1.3.5
Default Setting
You can change some parameters that the printer refers to at printer initialization.
1.3.5.1
Setting Method
Refer to the following flowchart for default setting.
Figure 1-14.
Flowchart for Default Setting
Table 1-37.
Buzzer Status
Printer status
Beep sounds
Paper out error
•••
Release lever operation error
•••
Cover open error
•••
Paper eject error
•••
Panel operation
•
Fatal error *1
-----
Holding down
Item
↓
(Font)
button, turn the printer on.
Language selection sheet.
Change the
language?
Press
Item
↓
(Font)
button to
select the aimed language.
Press
Set (Tear Off/Bin)
button.
The current setting value
and the language that was
selected will be printed.
Referring to
Font
LEDs,
press
Item
↓
(Font)
or
Item
↑
(Pitch)
button to select
the menu.
Referring to
Pitch
LEDs,
press
Set (Tear Off/Bin)
button to change the setting
value.
Finish?
Press
Menu (Pitch & Tear
Off/Bin)
button. *
Finish?
The select sheet will be
printed.
Press
Set (Tear Off/Bin)
button.
START
END
YES
NO
YES
YES
NO
NO
* The printer will exit from the default setting mode after storing
the setting into non-volatile memory.