Epson ActionDesk 4000 User Manual - Page 45

Enter., RESET, Ctrl + Alt + Del., Problems

Get Epson ActionDesk 4000 PDF manuals and user guides View all Epson ActionDesk 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

If you set the Diskette Access option to Supervisor, you can access a diskette drive only if the Supervisor password is entered during startup. If the User password is entered, you cannot access the diskette drive. Follow these steps to enter your password when you see the password prompt: 1. Type your password. You see a rectangle for each character you type. Then press Enter. 2. After you type the password correctly and press Enter, the computer loads the operating system (or starts SETUP). If you don't enter the correct password the first time you type it, you can try two more times. If you haven't entered the correct password on the third try, the computer locks up to prevent unauthorized access. You see the message: System Disabled! You must turn off the computer and start over. You can reset the computer using the RESET button but you cannot reset the computer by pressing Ctrl + Alt + Del. Note If you want to delete your password, you must run the SETUP program and follow the instructions for deleting a password in Chapter 2. If you do not remember your password, see "Password Problems" in Chapter 7. Using Your Computer 3-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
If you set the
Diskette
Access option to Supervisor, you
can access a diskette drive only if the Supervisor password is
entered during startup. If the User password is entered, you
cannot access the diskette drive.
Follow these steps to enter your password when you see the
password prompt:
1.
Type your password. You see a rectangle for each character
you type. Then press
Enter.
2.
After you type the password correctly and press
Enter,
the
computer loads the operating system (or starts SETUP).
If you don’t enter the correct password the first time you type
it, you can try two more times. If you haven’t entered the
correct password on the third try, the computer locks up to
prevent unauthorized access. You see the message:
System Disabled!
You must turn off the computer and start over. You
can reset
the computer using the
RESET
button but you cannot reset the
computer by pressing
Ctrl + Alt + Del.
Note
If you
want
to delete your password, you must run the
SETUP program and follow the instructions for deleting a
password in Chapter 2.
If you do not remember your password, see “Password
Problems” in Chapter 7.
Using
Your
Computer
3-5