Epson ActionDesk 4000 User Manual - Page 89

Removing a Hard Disk Drive From the Internal Drive, Installing a Drive in the Upper External Drive Bay

Get Epson ActionDesk 4000 PDF manuals and user guides View all Epson ActionDesk 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Removing a Hard Disk Drive From the Internal Drive Bay To remove a hard disk drive, reverse the installation steps outlined above. Then disconnect the hard disk drive ribbon cable and the power supply cable from the back of the drive. When you disconnect the cables, grasp the connectors and pull them straight out so you do not bend the pins; do not pull on the cables. Use the screws to again secure the hard disk drive mounting bracket to the base of the computer. Installing a Drive in the Upper External Drive Bay Your system comes with a 3.5-inch diskette drive installed in the lower externally accessible drive bay. You can also install a diskette drive, a CD-ROM, or a tape drive in the upper externally accessible drive bay. If you are installing a tape drive with a standard 5.25-inch diskette drive connector, you can connect it using the diskette drive cable that came with your system. Before you install a drive in the upper drive bay, remove the cover. Once you have the drive installed, replace the cover, following the instructions in Chapter 4. Installing and Removing Drives 5-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
Removing a Hard Disk Drive From the Internal
Drive
Bay
To remove a hard disk drive, reverse the installation steps
outlined above. Then disconnect the hard disk drive ribbon
cable and the power supply cable from the back of the drive.
When you disconnect the cables, grasp the connectors and pull
them straight out so you do not bend the pins; do not pull on
the cables. Use the screws to again secure the hard disk drive
mounting bracket to the base of the computer.
Installing a Drive in the Upper External Drive Bay
Your system comes with a 3.5-inch diskette drive installed in
the lower externally accessible drive bay. You can also install a
diskette drive, a CD-ROM, or a tape drive in the upper
externally accessible drive bay.
If you are installing a tape drive with a standard 5.25-inch
diskette drive connector, you can connect it using the diskette
drive cable that came with your system.
Before you install a drive in the upper drive bay, remove the
cover. Once you have the drive installed, replace the cover,
following the instructions in Chapter 4.
Installing and Removing Drives
5-13