Epson ActionDesk 4000 User Manual - Page 92
Connecting the Drive and Power Cables, connected to the bottom diskette drive. Use the other
 |
View all Epson ActionDesk 4000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 92 highlights
Connecting the Drive and Power Cables To connect the drive to the computer, you need to connect both the drive ribbon cable and a power supply cable. Follow the steps below. 1. If you are installing a diskette drive, locate the diskette drive ribbon cable. (The connector in the middle of the cable is already connected to the system board.) 2. If you are installing a second diskette drive or a tape drive with a card-edge connector, one end of the cable is connected to the bottom diskette drive. Use the other connector on the ribbon cable to connect the drive to the system board. Make sure you align the key-way (the plastic divider) with the gap in the drive connector, as shown below. 5-16 Installing and Removing Drives
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87 -
88 -
89 -
90 -
91 -
92 -
93 -
94 -
95 -
96 -
97 -
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
 |
 |
Connecting the Drive and Power Cables
To connect the drive to the computer, you need to connect both
the drive ribbon cable and a power supply cable. Follow the
steps below.
1.
If you are installing a diskette drive, locate the diskette drive
ribbon cable. (The connector in the middle of the cable is
already connected to the system board.)
2.
If you are installing a second diskette drive or a tape drive
with a card-edge connector, one end of the cable is
connected to the bottom diskette drive. Use the other
connector on the ribbon cable to connect the drive to the
system board.
Make sure you align the key-way (the plastic divider) with
the gap in the drive connector, as shown below.
5-16
Installing and Removing
Drives