Epson ActionDesk 4000 User Manual - Page 82

Connecting the drive and power cables to the drive, containing pin 1.

Get Epson ActionDesk 4000 PDF manuals and user guides View all Epson ActionDesk 4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Connecting the drive and power cables to the drive Follow the steps below to connect the hard disk drive ribbon cable and a power supply cable to the drive: 1. Locate the hard disk drive connector on the end of the hard disk drive ribbon cable. 2. Locate pin 1 on the drive connector. If you do not see it on the connector casing, turn the drive over so you can see the drive's circuit board, as shown below. There is a "1" or "2" printed on the board to identify the side of the connector containing pin 1. 3. Position the connector on the cable so that the red wire aligns with pin 1 on the drive. 4. Make sure the holes in the cable connector fit over all the pins; then push in the connector. 5-6 Installing and Removing Drives

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
Connecting the drive and power cables to the drive
Follow the steps below to connect the hard disk drive ribbon
cable and a power supply cable to the drive:
1.
Locate the hard disk drive connector on the end of the hard
disk drive ribbon cable.
2.
Locate pin 1 on the drive connector. If you do not see it on
the connector casing, turn the drive over so you can see the
drive’s circuit board, as shown below. There is a “1” or “2”
printed on the board to identify the side of the connector
containing pin 1.
3.
Position the connector on the cable so that the red wire
aligns with pin 1 on the drive.
4.
Make sure the holes in the cable connector fit over all the
pins; then push in the connector.
5-6
Installing and Removing Drives